Filter
Top Products
If you are having problems with your product, check this list of problems and possible solutions before
requesting service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number of
your product before you call. This information appears on the back of the product. Also, please take a
moment to identify the problem you are having, and be prepared to explain this to the representative. If
you believe the representative will need to help you with operations, please stay near the product. Our
representatives will be happy to assist you.
No power
• Connect the power plug completely to an AC (alternating current) outlet.
• Turn on the power.
Power Failure
• The VCR may lose timer recordings, the clock and channel settings, and the language selection if the
power fails. Follow the steps on pages 11 and 15 to reset the language, channels, and clock. Then, see
pages 28-30 to reprogram your timer recordings.
The VCR will not record a TV program.
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable). Details are on pages 6-10.
• Make sure the tape has a record tab. Details are on page 5.
• Check the TV/VCR position. Details are on page 22.
• Check the CH3/CH4 switch. Details are on pages 6-9.
The VCR will not perform a timer recording.
• Make sure you set the recording start and stop times correctly. Details are on pages 28-31.
• Make sure a tape is in the VCR and the tape has a record tab (page 5). If, after programming a timer
recording, you turn off the VCR power without putting a tape in the VCR, the Timer light will blink.
• If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.
• Make sure the VCR power is off.
• Make sure you have set the clock correctly. Details are on page 15.
• The VCR may not perform or continue a timer recording if the power fails.
• If you have a Cable Box/Direct Broadcast System, you will program timer recordings differently. Details
are on page 8.
• Finish programming a timer recording at least five minutes before the recording should begin.
• 12 p.m. is noon; 12 a.m. is midnight.
There is no playback picture or the playback picture is noisy or contains streaks.
• Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch.
• Make sure the VCR is in VCR position. (The VCR/TV light will appear on the display panel.)
• Adjust channel 03 or 04 at the TV.
• Adjust the tracking. Details are on page 37.
• TVs that are too close to the VCR can cause interference during tape playback. Move the VCR away
from the TV.
The remote control will not operate the VCR.
• Make sure the VCR/TV light appears on the display panel. If it does not, press the VCR/TV button once.
• Aim the remote control directly at the VCR’s remote sensor. Details are on page 22.
• Remove all obstacles between the remote control and the VCR.
• Inspect and/or replace the batteries in the remote control. Details are on page 5.
The Number buttons won’t work for channels above 69.
• Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter chan-
nel numbers as a three-digit number. If you are using an antenna (not a cable signal), you may only select
channels 2-69. Details are on page 18.
You cannot watch TV programs normally.
• Put the VCR in TV position, then change channels at the TV. (Press the VCR/TV button so that the
VCR/TV light disappears from the display panel. Details are on page 22.)
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable). Details are on pages 6-10.
42 Helpful Hints
mvr630mg.QX33 2/11/02 12:05 PM Page 42