Mitsumi electronic WD-C657 Flat Panel Television User Manual


 
54 6. NetCommand
Before You Begin
1. ConnectyourA/VdevicestotheTVandconnect
yourA/VreceivertotheTVandtheDVDplayer.
Seechapter2,“TVConnections,”forsuggestions.
2. Openthe Inputs > AVRmenu.
Note: ThetermsInput 1Input 4usedintheAVR
screenaretemporaryplaceholdernames.They
refertotheA/VreceiverinputsforwhichtheTV
canlearnIRcodes.
Setup 1: Automatic A/V Receiver Switching to Its TV
Audio Input
MostdevicesaresetupliketheVCRinthisexample,in
whichanalogaudiofromthedeviceissentthroughthe
TV.
Usethissetupfor:
• Sourcesprovidingonlyanalogstereooutput,such
asaVCR
• Audiofrom
ANT 1
and
ANT 2
57
"/5
"/5
BVEJPWJEFP
*ODPNJOH
$PBYJBM
$BCMF
"73FDFJWFS
%7%BVEJP
JOQVU
57BVEJP
JOQVU
57BVEJP
PVU
EJHJUBMPS
BOBMPHBVEJP
GSPN57
BOBMPHBVEJP
WJEFP
WJEFP
BOBMPHBVEJP
7$3XJUI
"OBMPH
"VEJP
Setup 1: A/V receiver audio from the TV’s digital or
analog audio output (
DIGITAL AUDIO OUT
or
AVR AUDIO
OUTPUT
)
1. UnderLearn/Name,press tohighlight
theareanexttoInput 1.
Inthisexample,theIRcodefortheA/Vreceiver’s
TV Audio
inputwillbe“learned”asInput 1.
2. Press
ENTER
ontheTV’sremotecontrol.
3. WhilethetextInput1isflashing,pressandholdthe
TV INPUT
keyontheA/V receiver’sremotecontrol.
4. WhenacheckappearsnexttoInput 1,releasethe
TV INPUT
key.
Setup to Control Automatic Switching of
A/V Receiver Audio Inputs
Twodifferentsetupsaredescribedhere:
Setup 1:AutomaticA/VReceiverSwitchingtoTV
AudioInput
Setup 2:AutomaticA/VReceiverSwitchingfora
devicesendingaudiodirectlytotheA/Vreceiver
• AudioAvailablefromTVonly:UseSetup1.
Audiofrom
ANT 1
and
ANT 2
mustbesenttothe
A/VreceiverfromtheTV’sDIGITAL AUDIO OUTor
analog
AVR AUDIO OUTPUT
.
UseSetup1tomaketheA/Vreceiverswitchto
itsdesignatedTVaudioinputwhenviewingthese
sources.
• HDMIDigitalStereoAudio:UseSetup1
DigitalstereoaudiofromanHDMIconnection
isavailablebothindigitalformat(fromtheTV’s
DIGITAL AUDIO OUT)jackandinanalogformat
(fromtheTV’s
AVR AUDIO OUTPUT
jack).
• AnalogStereoAudio:UseSetup1.
Audiofromsourceswithonlyanalogstereooutput
(suchasaVCR)canbesenteitherdirectlytothe
A/VreceiverorthroughtotheTVandthenontothe
A/Vreceiver.
Mitsubishirecommendsyousendaudiothrough
theTVasshownintheexample.Setup1causes
theA/Vreceivertoswitchtoitsinputdesignatedfor
TVaudio.
IfyouhaveadigitalA/Vreceiver,theTVmakesthe
audioavailablebyconvertinganalogaudiotoa
digitaloutput.
• DigitalSurroundSound:UseSetup2.
Adevicecansenddigitalsurroundsoundsuchas
DolbyDigitalorDTSdirectlytotheA/Vreceiver,
bypassingtheTVentirely.Thedevicemightbe
aDVDplayer,cablebox,orsatellitereceiver,and
couldhaveHDMIoutput.ADVDplayerisusedin
thisexample.
Yoursetupmayincludeadditionaldeviceswith
digitalsurroundsoundconnecteddirectlytothe
A/Vreceiver.ThesedevicesmightbeaDVDplayer
plusacableboxorsatellitereceiver.
Set Up NetCommand Control of an
A/V Receiver, continued
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
•
physically connected the TV to the A/V receiver
•
selected the A/V receiver for audio.
Press
AUDIO, then to show the Speakers option, then
to select the A/V Receiver.
• “
learned” the IR codes for the A/V receiver
inputs
• chosenthecorrectinputintheNetCommand
A/V Receiver Learn screen