Filter
Top Products
10
GB
To learn remote commands from the original remote control into the NAD HTR-1:
1 Position the original remote control 3 to 5 cm away from the HTR-1’s Infrared receiver, located at the bottom
of the remote control (see drawing), with the original’s remote transmission window or LED (usually at the top)
pointing towards to the HTR-1’s Infrared receiver.
2 Press the POWER ON/OFF (No. 2) and MUTE keys (No. 14) together for approximately 2 seconds until STATUS
LED (No.1) stays red.
3 Press the required DEVICE key (No.3); the DEVICE key will light up.
4 Using the numeric key-pad (No. 10) engage Learning Mode:
Press 55551 to learn remote commands for TUNER DEVICE key.
Press 55552 to learn remote commands for AMP DEVICE key.
Press 55553 to learn remote commands for CD DEVICE key.
Press 55554 to learn remote commands for DVD DEVICE key.
Press 55555 to learn remote commands for TV DEVICE key.
Press 55556 to learn remote commands for VCR DEVICE key.
Press 55557 to learn remote commands for CABLE DEVICE key.
Press 55558 to learn remote commands for CUSTOM DEVICE key.
If the entered code is correct, the STATUS LED will flash once. If the code is wrong, the STATUS LED will flash
twice.
5 Press and release the function key on the HTR-1, which you want to duplicate/learn a similar function from the
original remote into; the DEVICE key flashes once.
6 Press and hold down the function key on the original remote. When the HTR-1 has finished copying the code,
the STATUS LED will then flash once. Release the key on the original remote. If the STATUS LED flashes twice,
an error has occurred in the learning process; repeat the learning process from step 5 onwards.
7 To program the next function key for the same device repeat steps 5-6.
8 When you have finished programming the various commands for the selected device, press the DEVICE key.
The STATUS LED and DEVICE will extinguish. The remote commands have now been learned and stored, the
HTR-1 is ready to be used with the device.
NOTE
If no key is pressed for over 10 seconds, the HTR-1 will switch back from learning mode to normal use mode.
SETTING UP AND USING MACRO FUNCTION
The Macro function allows you to send up to 6 remote commands with just one key press. This can be useful, for
example to switch on your AV receiver, TV and DVD player, select the DVD input on the receiver and engage the
DVD Play function with a single key press.
For each of the 8 devices, a Macro function can be set up:
1 Press the POWER ON/OFF (No. 2) and MUTE keys (No. 14) together for approximately 2 seconds until STATUS
LED (No.1) stays red.
2 Press the required DEVICE key (No.3); the DEVICE key will light up.
3 Using the numeric key-pad (No. 10) engage Macro Setup Mode:
Press 77771 to record Macros for TUNER DEVICE key.
Press 77772 to record Macros for AMP DEVICE key.
Press 77773 to record Macros for CD DEVICE key.
Press 77774 to record Macros for DVD DEVICE key.
Press 77775 to record Macros for TV DEVICE key.
Press 77776 to record Macros for VCR DEVICE key.
Press 77777 to record Macros for CABLE DEVICE key.
Press 77778 to record Macros for CUSTOM DEVICE key.
If the entered code is correct, the STATUS LED will flash once. If the code is wrong, the STATUS LED will flash
twice.
4 Record your Macro by selecting the functions you wish to carry out when Macro is selected, just as if you were
using the remote control. You can switch devices to have remote commands from other devices within the
same Macro.
5 Press the Macro key (No. 23) to store the Macro. The STATUS LED and DEVICE key will go out and the Macro
is programmed.
NOTE
Some devices may not be capable in executing remote commands in rapid succession. When recording your
macro, this problem can be avoided by alternating each commands for the various devices, see example below.
HTR1 manual 120mm 20/4/01 8:17 pm Page 10