Filter
Top Products
26
VQT3A92
Reference
Troubleshooting guide
Before requesting service, please perform
the following steps.
The following do not indicate a problem with this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
∫ Unit doesn’t respond to remote
control or front panel buttons.
Disconnect the power cord, wait 1 minute, then reconnect
the power cord.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is on, press and hold [OK], [B] and [Y] on
the remote control at the same time for more than
5 seconds.
– “00 rEt” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “06 FtO” is displayed on
the unit’s display.
3 Press [OK] on the remote control or [< OPEN/CLOSE]
on the unit.
To return to the factory preset.
¾
Select “Yes” in “Restore Default Settings” in the Setup
menu. (> 25)
To return all settings to the factory preset.
¾
Reset the unit as follows:
1 While the unit is on, press and hold [OK], [B] and [Y] on
the remote control at the same time for more than
5 seconds.
– “00 rEt” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “08 FIn” is displayed on
the unit’s display.
3 Press and hold [OK] on the remote control or [< OPEN/
CLOSE] on the unit for at least 4 seconds.
The remote control doesn’t work properly.
¾
Change the batteries for the remote control. (> 4)
¾
The remote control and main unit are using different
codes. If “SEt ” is displayed on the unit’s display when
a button is pressed on the remote control, change the
code on the remote control. (> 25)
The TV tuner mode is not displayed when
the TV is switched on.
¾
This phenomenon may occur, depending on the TV
setting, when “Quick Start” is set to “On”.
– Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾
The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] and [Y] on
the remote control at the same time for more than
5 seconds.
– “00 rEt” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “03 VL” is displayed on
the unit’s display.
3 Press [OK] on the remote control or [< OPEN/CLOSE]
on the unit.
This unit does not recognize the USB
connection correctly.
¾
If inserted during playback the USB device may not be
recognized by this unit.
¾
Disconnect and reconnect the USB cable. If it still does
not recognize the connection, turn the power of this unit
off and on again.
¾
USB devices connected using a USB hub may not be
recognized by this unit.
¾
If you connect USB HDD to this unit, use USB extension
cable that is supplied with the HDD.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies.
(> 12)
4
Make the following checks and visit our
website for more information.
For USA :
www.panasonic.com/help
Enter the model number.
For Canada :
http://www.panasonic.ca
4
Or visit our website to find a service
center.
You can find a service center near you easily on our
website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” (> 33) or “Limited Warranty (Only for
CANADA)” (> 34).
General operation
VQT3A92~Body_eng.fm 26 ページ ２０１０年１２月２２日 水曜日 午前１０時４６分