Filter
Top Products
12
Recording from an external source
This function can be used to make up an edited tape from
other recordings or video sources.
A new scene can be added to the end of previous one.
Preparations
• Connect a video movie camera or another VCR to this VCR
as shown.
• Display the VCR picture on the TV.
• Insert the cassette on which the copying is to be performed,
and make sure that its erasure prevention tab is not broken
out.
• Select the audio/video source required by pressing
[INPUT SELECT] (6) to set A1 or A2.
A1: Through the AV1 (AUDIO IN/VIDEO IN) sockets.
A2: Through the AV2 (AUDIO IN/VIDEO IN) sockets on
front panel.
• Use the L and R connectors for operations in the normal
(monaural) mode.
Operations
1 Press [PLAY] (8) to start playback.
2 At the point where you want to join a new scene, press
[PAUSE/SLOW] (29) to put it in the still playback
mode.
3 Press [REC] (15) to put it in the recording pause mode.
4 Start playback on the source unit and search for the
point from which you want to record (copy) onto this
VCR.
5 When that point is reached, press [PAUSE/SLOW] (29)
again to start recording the new picture and sound
from the playback unit.
6 To record (copy) additional scenes, press [PAUSE/
SLOW] (29) to put this VCR in the recording pause
mode and then perform above steps 4 and 5 again.
7 At the point where you want to stop recording, press
[STOP] (12) to finish recording.
Note:
• If you leave the VCR in the recording pause mode for more
than 5 minutes in step 3 or 6, the VCR automatically
switches over to stop mode to protect the video heads.
To Delete all of a Cassette’s
Contents (Tape Refresh Function)
You can delete a cassette contents (the picture, the sound
and the Jet Navigator data) all at once.
Operations
1 Be sure to set [JET NAVIGATOR] to [ON] when you
want to delete all contents of a cassette that is
recorded while setting [JET NAVIGATOR] to [ON].
Be sure to set [JET NAVIGATOR] to [OFF] when you
want to delete all contents of a cassette that is
recorded while setting [JET NAVIGATOR] to [OFF] or is
recorded on another VCR. (See page 8.)
2 Insert a cassette that you want to delete the cassette
contents.
3 Press [MENU] (9) to display the Main menu on the
screen.
4 Press [43] (28) to select the
[TAPE REFRESH], and then press
the [ENTER] (26).
5 Press [ENTER] (26) for 2 seconds or more to start the
tape refresh function.
The tape is rewound to the beginning, and it is fast-forwarded
with the tape refresh function.
When the tape reaches the end, the VCR automatically
rewinds it to the beginning.
Note:
• When a video cassette with a broken off erasure prevention
tab is inserted, this function is not activated.
TIMER REC
/ I
REC/OTR
VIDEO
IN (AV1) OUT
L
AUDIO
R
(2)
(1)
(3)
(1) AV 1
(VIDEO IN (43)/AUDIO IN (46))
(2) AV 2
(VIDEO IN (36)/AUDIO IN (37))
(3) Other VCR or Video movie
camera
Recording VCR
TIMER REC
/ I
REC/OTR
(1)
¢
(1) Other VCR or Video movie
camera
¢ Audio Cable (Not supplied)
TAPE REFRESH
START:
ENTER
END:STOP
TAPE REFRESH
END:STOP
NV-HV61GL_GN.book 12 ページ ２００４年２月１９日 木曜日 午後１時２６分