Filter
Top Products
6
LSQT0869
If Auto Tuning stops halfway by turning the VCR off or a
power failure,
Or if the VCR is turned on without the aerial connected
and all channels are skipped:
1 Disconnect the mains lead and then reconnect it.
2 Turn off the VCR and then turn it on.
• Auto Tuning commences.
Auto Tuning Using the On Screen Display
The VCR is tuned automatically by Plug in Auto Tuning.
However, Auto Tuning using the On Screen Display should be
performed according to the following method if necessary.
Preparations
• Confirm that the TV is on and the VCR viewing channel is
selected.
• Turn on the VCR and select any programme position except
A1 or A2.
Operations
1 Press [MENU] (9) to display the
Main menu on the TV screen.
2 Press [43] (28) to select
[TUNER PRESET] then press
[ENTER] (26).
3 Press [43] (28) to select
[AUTO TUNE] then press [21]
(28) to start the Auto Tuning.
• When Auto Tuning is completed,
the On Screen Display
disappears and programme
position 1 is selected.
Channels that can be received
Notes:
• Auto Tuning searches for TV stations from VHF minimum to
UHF maximum and memorizes every tuned programme
position. Other programme positions are skipped.
• Auto Tuning takes 5 or more minutes to complete its search.
Manual Tuning Procedure
If the VCR is not correctly tuned by Auto Tuning, follow the
procedure below.
1 Press [MENU] (9) to display the Main menu on the TV
screen.
2 Press [43] (28) to select [TUNER PRESET] then
press [ENTER] (26).
3 Press [43] (28) to select [CH] then select the channel
number you want to tune by pressing [21] (28).
4 Confirm that [CLEAR] is set to [OFF].
5 Press [43] (28) to select [SEARCH] then press [21]
(28) to start the Manual Tuning.
• If the desired TV station has not been tuned, press [21]
(28) again.
• Press [MENU] (9) and repeat steps 3-5 for each
programme position you want to tune to a station.
6 Press [MENU] (9) three times to exit the On Screen
Display.
Direct Tuning
Follow steps 1 to 4 of Manual Tuning Procedure.
5
Press [43] (28) to select [SEARCH].
6
Press [Numeric] (3) to enter the number of the desired
programme position.
For the 5A and 9A channels, input the following
numbers:
90 for CH-5A, 91 for CH-9A. (Example for NV-HV62GL)
• For other channels that require tuning, repeat steps 3, 4,
5
,
6
.
7
Press [MENU] (9) twice to exit the On Screen Display.
Fine Tuning Procedure
Follow steps 1 to 4 of Manual Tuning Procedure.
5
Press [43] (28) to select
[FINE] then press [21] (28) to
obtain the best tuning condition.
• Press [ENTER] (26) to return the
tuning to its former state.
6
Press [MENU] (9) to exit the On
Screen Display.
Blanking of Unused Programme Positions
Follow steps 1 to 3 of Manual Tuning Procedure.
4 Press [43] (28) to select [CLEAR] then press
[21] (28) to select [ON].
• Repeat steps 3, 4 for other unused programme positions
to skip during the selection of programme positions.
• To cancel the blanking of a programme position, select
that programme position then set [CLEAR] to [OFF].
5 Press [MENU] (9) twice to exit the On Screen Display.
VHF UHF CATV
NV-HV62GL 0-12 28-69 45-470 MHz
NV-HV62GN 1-11 21-69 44-470 MHz
CH 1
SEARCH
END : MENU
100
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 1
CLEAR
AUTO TUNE
SEARCH
FINE
END : MENU
SELECT:
TUNER PRESET
[OFF]
[
3]
MENU
SELECT
END
: , ENTER
:MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY
0PROG.
MENU
SELECT
END
: , ENTER
:MENU
CLOCK SET
TUNER PRESET
SYSTEM
OPTION
TAPE REFRESH
NAVI MEMORY
0PROG.
The number displayed here
is the number of channels
still to be auto tuned.
CH 2
END: MENU
CH 2 SEARCH 74
END: MENU
SEARCH
CH 2 AFC: ENTER
FINE : END: MENU
LSQT0869.book 6 ページ ２００５年２月２３日 水曜日 午後８時４７分