Filter
Top Products
25
MONO broadcast
Normal monaural sound broadcast.
SAP broadcast
Secondary Audio Program (sub language)
broadcast. Select SAP audio mode for the
sub language.
MTS Stereo broadcast
Multi-channel Television Sound Stereo
broadcast. Select STEREO audio mode.
• If stereo broadcast is weak and display
flickers, select MONO audio mode for
possibly better results.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main
language) and Secondary Audio Program
(sub language) broadcasts are being
received simultaneously. Select STEREO or
SAP audio mode.
The following are possible audio broadcast types and on-screen
displays. The signal being received is indicated with an “ ” mark
while the selected audio mode is indicated with an arrow.
Receivable Broadcast Types
Audio Mode for Recording
1
2
Do a recording.
See page 15.
3
• Arrow indicates
selection.
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
ABC
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
ABC
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
ABC
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
ABC
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
MTS Broadcast/ VHS Hi-Fi Stereo System
Audio Mode for Playback
Start playback.
See page 14.
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo
tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a
stereo TV or an external stereo amplifier and speakers. (See top of this page.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
• Arrow indicates
selection.
Equipped with
®
-TV Noise
Reduction for true MTS
reproduction.
®
-TV Noise
Reduction is required for good
stereo separation and audio
fidelity.
®
is a registered
trademark, and is licensed by
®
Technology Licensing.
• Select “HIFI(L/R)” or
“HIFI(L)” or “HIFI(R)”
to listen to stereo
recordings in stereo
sound. Select
“NORMAL” for
monaural sound.
Stereo Amplifier
AUDIO IN
R
L
VCR
R
L
R
OUT TO TV
VHF/UHF
TV
R
L
AUDIO OUT
DISPLAY
SAP/Hi-Fi
Connection
Make the Audio/Video Connection as shown on the
previous page.
• You can use a TV connected to a Stereo amplifier and
speakers instead of a Stereo TV.
To display the broadcast signal being received,
➛➛
➛➛
➛ press DISPLAY.
Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)
Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)
Press SAP/ Hi-Fi
repeatedly to
select desired
mode.
1
2
3
H
I
F
I
: L
/
R
H
I
F
I
: L
H
I
F
I
:
R
N
ORM
AL
Notes
Advanced
Operation
Press SAP/ Hi-Fi
repeatedly to select
desired mode.
• Refer to “Receivable
Broadcast Types” above.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2925