Filter
Top Products
16
QUAD SEQ SETUP
STEP CH SEC STEP CH SEC
1 4A 2S 9 -- 0S
2 4B 2S 10 -- 0S
3 4C 2S 11 -- 0S
4 4D 2S 12 -- 0S
5 -- 0S 13 -- 0S
6 -- 0S 14 -- 0S
7 -- 0S 15 -- 0S
8 -- 0S 16 -- 0S
QUAD SEQ SETUP
STEP CH SEC STEP CH SEC
1 4A 2S 9 -- 0S
2 4B 2S 10 -- 0S
3 9 2S 11 -- 0S
4 -- 0S 12 -- 0S
5 -- 0S 13 -- 0S
6 -- 0S 14 -- 0S
7 -- 0S 15 -- 0S
8 -- 0S 16 -- 0S
<WJ-FS316/FS416>
<WJ-FS309/FS409>
1-2. SEQ MODE
This item lets you select the Sequence pattern for display
on the Multiscreen monitor.
1. Move the cursor to the SEQ MODE parameter.
2. Select the desired Sequence mode or dwell time by
pressing the + or – button.
The initial factory setting is QUAD.
QUAD: Pictures are displayed on a quad screen in the
selected sequence mode and dwell time.
Note: In the 9-channel pattern of WJ-FS309/FS409,
channels 1 - 8 are displayed on two quad screen
pages. Channel 9 is not displayed.
3+1→2S: All segments of the quad screen, except the
bottom right, display pictures in the selected
sequence and dwell time.
Dwell time: Can be set to 2S - 30S.
Note: The display position of quad pictures in
Sequence mode is fixed for channels 1 to 3. It can-
not be changed.
(Example)
8+1→2S: All segments of the 9-segment screen,
except the bottom right, display pictures in the
selected sequence and dwell time.
Dwell time: Can be set to 2S - 30S.
(Example)
Notes:
• The display position of 9-segment screen pictures
in Sequence mode is fixed for channels 1 to 8. It
cannot be changed.
• This function is available only for the WJ-
FS316/FS416 Video Multiplexer.
1
3 4
2
SEQ
Channels 4 - 16 flash
at 2-second intervals (dwell time 2S).
1 3
4 5
2
6
7 8 9
SEQ
Channels 9 - 16 flash
at 2-second intervals (dwell time 2S).
Step Assignment
1. Move the cursor to the step number you desire to edit in
the CH area by pressing the cursor (C, D, A, B) but-
tons.
2. Select the desired camera channel in the CH area by
pressing the Increment (+) or Decrement (–) button.
1 - 16: Camera Channel
4A: 1 - 4 channel
4B: 5 - 8 channel
4C: 9 - 12 channel (only for WJ-FS316/FS416)
4D: 13 - 16 channel (only for WJ-FS316/FS416)
Note:
• 10-16 are not available for WJ-FS309/FS409.
• 9-segment or 16-segment screen does not display
in quad sequence.
– –: Not Assigned
3. Repeat the above procedures to assign other steps.
Dwell Time
1. Move the cursor to the SEC (Second) area by pressing
the cursor (C, D, A, B) buttons.
2. Select the desired dwell time in the SEC area by press-
ing the Increment (+) or Decrement (–) button.
Dwell Time can be selected between 0S and 30S.
Note: A step assigned a dwell time of 0S is skipped.