Filter
Top Products
SETUP BY ENTERING DEVICE CODE continued
11.Once you have found a suitable code, to store it, press the TV INDICATOR
key twice. The TV INDICATOR key will
flash twice and then go out as will the
STATUS INDICATOR.
12.If none of the TV codes listed for your brand of TV work correctly, select the
code that provides the best results. Alternatively, try the Library Search
method, which is fully explained further on in these instructions.
SET UP FOR VCR AND SAT
Repeat the same set-up method for your VCR and SAT, but remember to press
the VCR, SAT or DVD DEVICE INDICATOR key, and select the corresponding
Device Code listing.
SET-UP BY MANUAL CODE SEARCH
If you cannot identify a suitable Device Code for your equipment from the
Device Code List and have been unable to store a code when using Auto Code
Search you may try our library search method. (For many lesser known brands
codes may be present but not listed under that brand.) During the search
the selected DEVICE INDICATOR will flash at various speeds. The entire search
procedure may take several minutes to complete. The following instructions
use your television as an example for set-up using the Manual Code Search
method.
TV SETUP BY MANUAL CODE SEARCH
1. Turn on your TV
2. Hold down both POWER and MUTE keys on your RCx4
simultaneously until the STATUS INDICATOR LED lights up and stays red
(about 4 seconds).
3. Release the POWER and MUTE keys The STATUS INDICATOR should
still be lit. If not repeat step 2.
4. Press the TV DEVICE INDICATOR key once. The STATUS INDICATOR and the
DEVICE INDICATOR should now both be RED.
5. To search, aim your RCx4 at your TV.
6. Press the POWER key repeatedly for 2 seconds ON and 2 seconds OFF,
until your TV goes into standby mode (i.e. the TV switches OFF). Then
continue with step 7.If the TV INDICATOR key flashes twice and then goes
outbefore your TV goes into stanby mode you have reached the end of the
code library. Return to step 2 and repeat library search one more time.
7. Try the number keypad to see if your device switches ON again and the
keys work correctly. If your device does not switch ON, press the Mute
key and then the Power key to repeat the code so that the Device
comes ON.
Now try the number keypad. (NOTE: If you accidentally skipped
a code that turned your TV ON or OFF, you can return to the skipped code
by pressing the Mute key.)
8. If the code you have found does not work correctly, make sure that the TV
INDICATOR key and STATUS INDICATOR LED are still lit, before you repeat
steps 6 and 7 until you find a better code. If the indicator lights have gone
out, repeat the set-up procedure from step 2.
9. Once you are happy with the code found, press the TV INDICATOR key once
to store the code. The STATUS INDICATOR LED and DEVICE INDICATOR key
will turn off and set-up is complete.
VCR/DVD/SAT SETUP BY MANUAL CODE SEARCH
Simply repeat the above procedure to search for the Device Codes for your
VCR/SAT/DVD but instead of the TV DEVICE INDICATOR key press either the
VCR, SAT or DVD DEVICE INDICATOR key in step 4
OPERATING YOUR RCx4
Once you have set up your RCx4, it should operate similarly to your original
remote control and perform most or all of the main functions. To operate, just
aim it at your equipment, press the appropriate DEVICE INDICATOR key and
press the required function key. The DEVICE INDICATOR flashes during signal
transmission to confirm that a function key is in operation.
Please Note: The RCx4 can only duplicate functions that are on your original
remote control. Any extra keys on the RCx4 which are not on the original
will not function.
SHIFT Functions
To operate a secondary function, press SHIFT followed by the corresponding
function key. The SHIFT key remains functional for as long as any other key
is operated, or until 5 seconds have elapsed after the last key was pressed.
When the SHIFT key is operated, the STATUS INDICATOR lights up green and the
DEVICE INDICATOR key red while the SHIFT key is pressed down. The STATUS
INDICATOR then stays ON for another 5 seconds. The SHIFT key can be can-
celled before the 5 seconds time-out period by pressing the SHIFT key again.
DEVICE CODE RECALL - 888
The RCx4 has a special code which can be entered to find the code that has
been set for each device. ( e.g. after Code Search set-ups )
1. Press POWER and MUTE keys together until STATUS INDICATOR RED
LED lights up.
2. Then press the required DEVICE INDICATOR key [TV, SAT, VCR or DVD],
STATUS INDICATOR LED & DEVICE INDICATOR key will light up RED.
3. Key in Device Code Recall code 888 the STATUS INDICATOR RED
LED lights up and flashes 3 times.
• To find the first digit of your code, press 1 and then count the number of
times the STATUS INDICATOR LED flashes red.
• To find the second digit of your code, press 2 and then count the
number of times the STATUS INDICATOR LED flashes red.
• To find the third digit of your code, press 3 and then count the number
of times the STATUS INDICATOR LED flashes red.
[Note: If the STATUS INDICATOR LED does not flash at all the digit is zero
(duration between flashes is 1 sec.)]
E.G. Code=106, Number 1=1 flash, Number 2=no flash, Number 3=6
flashes.
5. Press Any Device key [TV, SAT, VCR or DVD] once to exit Device Code Recall.
(Note that the RCx4 will exit the Recall procedure if no key is pressed for
30 seconds)
KEY RECONFIGURATION - 777
1. Press POWER and MUTE keys together until STATUS INDICATOR RED
LED lights up.
2. If you are reconfiguring a SHIFT Function key, you must next press the
SHIFT key and the STATUS LED will change to GREEN.
TV
SATVCR
MENU
SHIFT
A/V
DVD
VOL
VOL
CH
CH
Step 2.
Figure 6.
STATUS
INDICATOR
DEVICE
INDICATOR
KEYS
TV
SATVCR
DVD
Figure 7.
Step 4.
4