Filter
Top Products
Preparation for use
This chapter shows you how to prepare the video
recorder use.The video recorder automatically
seeks out and stores all available TV channels.
1.
1.Select the desired language for the on-screen
menu by pressing or .
2.
2.Press .
3.
3.Confirm with .
The automatic TV channel search starts.
4.
4.'TIME' and 'DATE' will appear on the TV
screen.
5.
5.Check 'TIME'. If required, please change the
time with the number buttons .
6.
6.Check if the displayed settings for 'DAY',
'MONTH' and 'YEAR' are correct.
7.
7.When all information is correct, save by
pressing .
The preparation for use is now complete.
Manual TV channel search
In some cases it can occur that all of the TV
channels are not found and saved during the first
installation. In this case, the missing or coded TV
channels must be searched for and stored man-
ually.
1.
1.Switch on the TV set. If required, select the
programme number for the video recorder.
2.
2.Press .
The main menu will appear.
3.
3.Use or to select 'TUNER
SET UP'.Then press .
4.
4.Use or
to select 'MANUAL TUNING'. Then
press .
5.
5.Select 'PROG.' with or
.
Then press
.
6.
6.With or
or
, select the
desired programme number that you want to
use for the TV channel, e.g. 'P01'. Then press
.
7.
7.Select 'CHANNEL' with or ,
and confirm with .Then enter the
desired channel with
.
If you set
'
SKIP
'
on for a channel, this channel
will be ignored when going through the channels
with or .
PROG P–
PROG P
+
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
0..9
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
STATUS/EXIT
0..9
PROG P+
MENU
STOP C-LPLAY B-K
EN
'Aim' correctly
In the following sections, you require the remote
control for the first time. When using, always
aim the front of the remote control at the video
recorder and not at the TV.
Connecting additional devices
After you have connected additional devices
(satellite receiver, etc.) through the aerial cable,
switch them on.The automatic channel search
will recognise them and save them.
PLEASE WAIT
START FINISH
❚❚❚❚❚❚❚❚❚❚❚
❚❚❚❚❚❚❚❚❚❚❚❚
The video recorder does not find any TV
channels during the search
* Select channel 1 on the TV. Can you see the
saved TV channel on the TV?
If not, check the cable connection of the aerial
(aerial socket), video recorder, TV.
* The video recorder searches the entire fre-
quency range in order to find and save the
largest possible number of TV channels. It is pos-
sible that the TV channels in your country are
broadcast in a higher frequency range. As soon
as this range is reached during the search, the
video recorder will find the TV channels.
TIME --:--
DATE --/--/--
END=EXIT
4. Installing your video recorder
6
MANUAL TUNING
→PROG. P55
CHANNEL 055
SKIP [OFF]
VIDEO MODE [SECAM]
AUDIO MODE [DK]
SELECT
KL CHOOSE B
END=EXIT
What is a special channel?
TV channels are transmitted in certain pre-
defined frequency ranges.These ranges are
divided into channels.
A specific frequency/channel is assigned to each
TV station.
Certain frequency ranges are specified as special
channels (hyperband channels).
HE273ED(EN).QX3 03.3.12 1:47 PM Page 6