Filter
Top Products
1312
PLAY
PLAYPLAY
PLAY
STOP
STOPSTOP
STOPRE C
RE CREC
RE C PAUSE
PAUSEPA USE
PAUSE
SC AN
SC ANSCA N
SC AN
+
++
+
S
SS
SC
CC
CA
AA
AN
NN
N
PIP
PIPPIP
PIP
TOGGLE
TOGGLETOGGLE
TOGGLE
LEARN
LEARNLEARN
LEARN
VCR
VCRVCR
VCR
CBL
CBLCBL
CBL
TV
TVTV
TV
DVD
DVDDVD
DVD
SAT
SATSAT
SAT
PREV
PREVPREV
PREV
CHAN
CHANCHAN
CHAN
CO DE
CO DECODE
CO DE
SEARCH
SEARCHSEARCH
SEARCH
CD
CDCD
CD
POWER
POWERPOWER
POWER
MUTE
MUTEMU TE
MUTE
V
VV
VO
OO
OL
LL
L
+
++
+
ENTER
ENTERENTER
ENTER
TV/VCR
TV/VCRTV/VCR
TV/VCR
INFO/
INFO/INFO/
INFO/
SEL ECT
SEL ECTSELECT
SEL ECT
GUIDE
GUIDEGUIDE
GUIDE
MENU
MENUMENU
MENU
QUIT
QUITQUIT
QUIT
OK
OKOK
OK
CHAN
CHANCHAN
CHAN
+
++
+
C
CC
CH
HH
HA
AA
AN
NN
N
SLEEP
SLEEPSLEEP
SLEEP
REPEA T
REPEA TREPEA T
REPEA T
SUBTITLE
SUBTITLESUBTITLE
SUBTITLE
C
CC
CC
CC
C
+
++
+
CHAPTER
CHAPTERCHAPTER
CHAPTER
INPUT
INPUTINPUT
INPUT
AUX
AUXAUX
AUX
Tips On Learning
1. Use fresh batteries for both the Learning Remote and
the Original Remote.
2. Perform a Master clear (see page 15) before learning.
3. Place the original remote end-to-end with the
Learning Remote so the IR transmitters on both
remotes are directly in line with each other. Keep the
two remotes approximately one inch away from each
other.
4. Experiment by learning 2 or 3 commands initially (to
ensure compatibility and familiarity) and then carry
out a Master Clear before completely learning your
original remote’s commands.
5. Do not try to learn directly under an incandescent or
low-energy light as these can cause interference with
learning. Keep at least three feet away from any such
light sources.
Code Learning
Sleep Timer
The Sleep feature enables the remote to turn off the TV
after a period of 1 to 99 minutes. Remote is to be in TV
mode to set a Sleep Timer. This feature works even if
your TV does not have this feature.
1. Press and release the TV Mode key.
2. Press and hold the Sleep button until LED remains
on (occurring after approx. 2-3 seconds).
3. Release Sleep button.
4. Press and release the numeric keys (01-99) for the
time required. The LED will blink off to indicate
keypress acceptance and remain off after second
keypress.
5. TV Sleep Timer now set.
6. Leave the Remote pointing towards the TV with an
unobstructed path.
To cancel the Sleep Timer, press and hold the Sleep key
until the LED blinks or press and release the Power key
in TV Mode.
Code Identification
1. Press and hold Code Search button until the red
indicator stays on. Release the Code Search button.
2. Press and release the desired mode button (TV, VCR,
etc.).
The red indicator blinks, then stays lit.
3. Press and release the Code Search button. The
indicator light blinks off.
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9 in turn. When the indicator light blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4, this time
when the indicator light blinks off this is the second
digit.
6. Repeat step 4 again to find the third digit.
Code Identification
1, 3.
2.
4.