RCA RCR313BR Universal Remote User Manual

Open as PDF

of 6

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any Changes or modiﬁ cations not expressly approved by the

party responsible for compliance could void the user’s authority to

operate this equipment.

Industry Canada Regulatory Information

This class B digital apparatus complies with Canadian ICES-003

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme a la nome

NMB-003du Canada

• There is a possibility that a programmed code may only be

able to control some of your device features (for example,

only turns a device on and off). To conﬁ rm that the device

key is programmed with the correct code for maximum

functionality, test the device. Attempt to control a variety

of the device’s functions with the remote. If some of the

features of your devices don’t work, try programming the

remote with a different code in the list using the Direct Code

Entry Method, until you ﬁ nd the code that allows the remote

to control the majority of your device’s functions. Different

codes can provide different levels of functionality.

Problem: The POWER key does not light when you press a

key.

• You may have pressed an invalid key for the mode the

remote is in.

• Make sure the remote is in the correct mode by pressing

the corresponding device key (TV, SAT•CBL•STREAM,

DVD•VCR). This tells the remote which device to operate.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AA batteries, if necessary

(see the Battery Installation section).

Problem: The remote will not change channels on device.

• Make sure the remote is in the correct mode by pressing

the corresponding device key (TV, SAT•CBL•STREAM,

DVD•VCR). This tells the remote which device to operate.

• Press the OK key after you enter a channel number.

• Remove any obstacles between the remote and the device.

Make sure to aim the remote at the IR sensor on the device.

Problem: The device’s menu does not appear on the TV

screen.

• Make sure you have connected the device to your TV properly

and selected the correct input. (See your devices’ Owner’s

Manuals for proper connection procedures.)

• Make sure the remote is in the correct mode by pressing

the corresponding device key (TV, SAT•CBL•STREAM,

DVD•VCR). This tells the remote which device to operate.

• Menu access isn’t supported for all brands. You may need to

use your original remote control to access menu functions

for some devices.

For more information, please visit

www.RCAAudioVideo.com

Consumer Help Line: 1-800-420-7968

In most cases, the keys

on this remote perform

the same functions

as the keys on your

original remotes once

you’ve programmed this

remote to operate your

components. Many keys

on this remote have other

functions as well.

Illuminated

POWER key

serves as an indicator

light to provide feedback.

Device keys (TV,

SAT•CBL•

STREAM,

DVD•VCR) put the remote

in the right mode to

control your device.

LIGHT key ( ) turns

backlighting on/off.

GUIDE/HOME and MENU

access the same features

as the keys on your

original remotes.

Arrow keys act as

navigation keys for

streaming media players

as well as in menu and

guide systems for other

devices.

Battery Saver

Your universal remote control saves battery power by

automatically turning off if any key is pressed for more than

60 seconds. This saves your battery life should your remote

get stuck in a place where the keys remain depressed, such

as between sofa cushions.

Congratulations on your purchase of this 3-device RCA

Universal Remote Control. This remote features a library

of codes with the latest devices of all major brands, with

support for streaming media players as well. The navigation

keys have been redesigned to function seamlessly with the

more sophisticated menu and guide systems found in today’s

home entertainment devices.

Universal Remote Control

Owner’s Manual

RCR314WR / RCR313BR

Manual del Propietario (parte posterior)

Care and Maintenance

• Keep the remote dry. If it gets wet, wipe it dry

immediately.

• Use and store the remote only in normal temperature

environments.

• Handle the remote gently and carefully. Don’t drop it.

• Keep the remote away from dust and dirt.

• Wipe the remote with a damp cloth occasionally to keep it

looking new.

• Modifying or tampering with the remote’s internal devices

can cause malfunction and invalidate its warranty.

SAVE THIS MANUAL AND THE CODE LISTS!

Remote controls can sometimes lose their programming when

you change the batteries. Make sure you keep the manual and

code lists in a safe place so that you can reprogram the remote

if you need to.

Your universal remote requires two AA alkaline batteries

(batteries may or may not be included, depending on model).

To install the batteries:

1. Remove the battery compartment

cover.

2. Insert the batteries, matching the

batteries to the (+) and (–) marks

inside the battery compartment.

3. Push the battery cover back into

place.

Battery Precautions:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries.

• Always remove old, weak or worn-out batteries promptly

and recycle or dispose of them in accordance with Local

and National Regulations.

To use this universal remote with your home entertainment

system, ﬁ rst you need to program it to control your devices.

There are four ways you can program the universal remote

to operate your devices. Try them in the order listed here:

• The Brand Code Search searches through the codes

for select brands of devices.

• The Direct Code Entry lets you enter a code from the

accompanying code list for your brand of device.

• The Auto Code Search goes automatically through all

the codes for the device you’re trying to control.

• The Manual Code Search lets you manually go

through all the codes for the device you’re trying to

control.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote.

If some device features don’t work, go to the next step

to try a different code.

2. Repeat the Brand Code Search from the beginning.

When the device turns off for the ﬁ rst time, don’t

press the STOP key, which would store the same code.

Instead, with the unit now off, continue to press the

POWER key repeatedly until the unit turns back on.

3. Once the unit turns back on, you have found another

code that operates the device. Press the STOP key.

4. Test the key’s functionality again by attempting to

control a variety of the device’s functions. If the code

that has been stored controls the majority of the

device’s functions, programming is complete. If the

code stored does not give maximum functionality, try

another code.

Brand Code Search

The Brand Code Search goes through only the codes for one

of the select brands listed in the accompanying code list. If

your brand of device is listed, this search can be very quick

and easy.

TIPS: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•STREAM for

satellite receivers, cable boxes, digital TV converters, or

streaming media players and DVD•VCR for VCRs or DVD

players.

The POWER key serves as an indicator light during

programming, giving you feedback at each stage of the

process.

To exit without saving a new code at any point in the Brand

Code Search, press the

GO BACK key.

1. Manually turn on the device

you want to control.

4. Press and hold the device key you want to program.

While you’re holding down the device key, use your

other hand to press and hold the remote’s

POWER key

at the same time.

5. Wait until the POWER key comes on and stays on.

Then release both keys.

7. Point the remote directly at the

front panel of the device you want

to control. Press POWER on the

remote and wait 2 seconds. The

remote is testing a single code for

your device’s brand.

Did your device turn off?

YES: Press the STOP key to store the code. You’re

done! You’ve programmed this device key.

NO: Press

POWER again. The remote tests the next

code for your brand.

Keep pressing

POWER every 2 seconds until your

device turns off. When it does, press STOP.

3. Find your device’s brand in the

Brand Code list section of the

accompanying code list. Circle

the number for your brand and

keep the list handy.

Code Lists

Brand Codes are used for programming using the Brand Code Search

and Entry method outlined in the User’s Guide.

Lista de Códigos

Los códigos de las marcas son utilizados para programar utilizando

los métodos de búsqueda y entrada de códigos de marcas, resaltado

en la guía del usuario.

0123456789

RCA

PROSCAN

Insignia

JVC

Magnavox

Philips

PanasonicSamsungSharpSonyToshibaVizio

VCR

0123456789

RCA

PROSCAN

Apex JVC

Magnavox

Philips

PanasonicPioneerSamsungSharpSonyToshiba

DVD

SAT/CABLE

0123456789

RCA

PROSCAN

MotorolaDirecTV

Dish Network

Systems/

Echos

tar

General

Instruments

Hughes

Network

Systems

Scientific

Atlanta

Magnavox

Philips

AMNIO

ADB

Panasonic

Brand Code List/Lista de Códigos de Marcas

0123456789

Samsung

Magnavox

Philips

MitsubishiPanasonicSharpSony Toshiba

RCA

PROSCAN

JVC

Symphonic

Admiral .................................

Advent ...........................................

Aiko .........................................................

Akai .............................10812, 11675, 10060,

Albatron

....................................................................

America Action ..........................................................

Anam

........................................................................

AOC ........................................................................

Apex Digital

........................................10156, 107

Audiovox ...............................10451, 10180, 100

.............................................................10875, 1

Aventura .........................................................

Axion

.............................................................

Bell & Howell ..............................................

BenQ .........................................................

Bradford

..................................................

Broksonic ...............................................

Candle ..................................................

Carnivale ............................................

Carver

...............................................

Celera .............................................

Changhong ...................................

Citizen .........................................

Clarion

.......................................

Commercial Solutions ............

Concerto ...............................

Contec ..................................

Craig ...................................

Crosley .............................

Crown ............................

Curtis Mathes ..............

....................................

...................................

CXC ..........................

Cytron ...................

Daewoo ..............

Dell ....................

Denon ..............

Diamond Visio

Dumont ........

Durabrand .

Dwin

.........

Dynex .....

Electrogr

Electroh

Emerso

.........

Empr

Env

ESA

6. Look at the number you circled for

your device’s brand code number.

Press that number on the remote

keypad.

NOTES

Throughout the programming of each key, be sure to

keep the remote pointed at the IR sensor of the device

you are currently programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

maximum functionality. If some features don’t work, try

a different code. See the “Testing the Code for Maximum

Functionality” section below for more information.

During the Brand Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the

POWER key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The

POWER key blinks four times and turns off when the

remote has gone through all the codes. The remote exits

the Brand Code Search. If your device hasn’t turned off

yet, try a different search method.

Direct Code Entry

Direct Code Entry lets you enter a code from the

accompanying code list for your brand of device. It’s not as

easy as the other methods, but it’s potentially the fastest

method.

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program

(the POWER key comes on).

While you’re holding down the device key, use your

other hand enter the ﬁ rst ﬁ ve-digit code for your brand

in the code list (the POWER key goes off after the ﬁ rst

digit).

2. Find the Code List that came with

the remote. Locate the section for

the type of device you’re trying to

program, and ﬁ nd your brand in

that section. Circle the codes for

your brand and keep them handy.

Code Lists

Brand Codes are used for programming using the Brand Code Search

and Entry method outlined in the User’s Guide.

Lista de Códigos

Los códigos de las m

rcas son utilizados para programar utilizando

los métodos de búsqueda y entrada de códigos de marcas, resaltado

en la guía del usuario.

0123456789

RCA

PROS

CAN

Insignia

JVC

Magnavox

Phi

lips

PanasonicSamsungSharpS

onyToshibaViz

VCR

0123456789

RCA

PROSCAN

Apex J

Magnavox

Phil

ips

PanasonicPioneerSa

msungSharp SonyToshib

DVD

SAT/CABLE

0123456789

RCA

PROSCAN

MotorolaDirecTV

Dish Network

Systems/

Echostar

General

Instruments

Hughes

Network

Systems

Scientific

Atlan

Magnavox

Philips

AMNIO

ADB

Panasonic

Brand Code List/Lista de Códigos de Marcas

0123456789

Samsung

Magnavo

Philips

Mitsubish

i PanasonicSharpSony Toshiba

RCA

PROSCAN

JVC

ymphonic

Admiral .................................

Advent ...........................................

Aiko .........................................................

Akai .............................10812, 11675, 10060,

Albatron

....................................................................

Americ

a Action ..........................................................

Anam

........................................................................

AOC ........................................................................

Apex Digital

........................................10156, 107

Audiovox ...............................10451, 10180, 10

.............................................................10875, 1

Aventura .........................................................

Axion

.............................................................

Bell & Howell ..............................................

BenQ .........................................................

Bradford

..................................................

Broksonic ...............................................

Candle ...........................

.......................

Carnivale ............................................

Carver

...........................

....................

Celera .............................................

anghong ...................................

Citizen .........................................

Clarion

.......................................

Commercial Solutions ............

Concerto ...............................

Contec .................................

Craig ...................................

Crosley .............................

Cro

n ............................

Curtis Mathe

s ..............

....................................

...................................

CXC ..........................

Cytron ...................

Daew

o ..............

Dell ....................

Denon ..............

Diamon

d Visio

Dumont ........

Durabrand .

Dwin

.........

Dynex .....

Electrogr

Electroh

Eme

rso

.........

Empr

Env

ESA

NOTES

Remember to enter the code for future reference in the

box provided in the Code Retrieval section of this manual.

If your brand isn’t listed in the code list, use one of the

Code Search methods to program the remote control.

(Refer to the Auto and Manual Code Search methods.)

If you release the device key any time during the Direct

Code Entry procedure, the

POWER key blinks four times,

and the process is exited. The last programmed code

under the device key is retained.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different

code in the list.

4. When you’ve ﬁ nished entering the ﬁ ve-digit code, keep

holding down the device key and look at the POWER

key.

Is the POWER key on?

YES: You’re done! You’ve programmed this device key.

NO, it blinked four times and turned off: You have

either entered a code number that is not in the code lists

or missed a step in the code entry procedure. Try step 3

again.

1. Manually turn on the device you

want to control.

2. If you’re programming the TV or

SAT•CBL•STREAM key, go to step 3.

If you’re programming the

DVD•VCR key, you need

to tell the remote which kind of device you want this

key to control, VCR or DVD.

Press and hold the

DVD•VCR key. While you’re holding

down the DVD•VCR key, use your other hand to press

the number key for the type of device you want to

control with this key: 2 for VCR, 3 for DVD.

4. Wait until the POWER key comes on and stays on.

Then release both keys.

5. Point the remote directly at the front panel of the device

you want to control. Press POWER on the remote and

wait 2 seconds. The remote is testing a single code for

your device.

Did your device turn off?

YES: Press the STOP key to store

the code. You’re done! You’ve

programmed this device key.

NO: Press

POWER again. The

remote tests the next code for

your device.

Keep pressing POWER every 2

seconds until your device turns off.

When it does, press STOP.

TIP: Because there are so many codes, you may have to

press the POWER key many times—possibly hundreds of

times.

NOTES

Throughout the programming of each key, keep the

remote pointed at the IR sensor of the device you are

programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

maximum functionality. If some features don’t work, try

a different code. See the “Testing the Code for Maximum

Functionality” section below for more information.

During the Manual Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the

POWER key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The

POWER key blinks four times and turns off when the

remote has gone through all the codes. The remote exits

the Manual Code Search. If your device hasn’t turned off

yet, try a different search method.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote.

If some features of your devices don’t work, go to the

next step to try a different code.

2. Repeat the Manual Code Search from the beginning.

When the device turns off for the ﬁ rst time, don’t

press the STOP key, which would store the same code.

Instead, with the unit now off, continue to press the

POWER

key repeatedly until the unit turns back on.

3. Once the unit turns back on, you have found another

code that operates the device. Press the STOP key.

4. Test the key’s functionality again by trying a variety

of functions. If the code controls the majority of the

device’s functions, programming is complete. If the

code stored does not give maximum functionality, try

another code.

Code Retrieval

Once you’ve programmed the remote to control your

devices, you may want to record the codes for future

reference. If you used the Direct Code Entry method, this

is easy. Just ﬁ nd the codes you entered and make a note

of them in the boxes below. If you used one of the Code

Search methods to program your remote or if you used the

Direct Entry method but don’t remember the code, you will

need to retrieve each device’s ﬁ ve-digit code. Retrieving

the actual code and writing it down will save you time

if you ever need to program the remote again (e.g., if

programming is lost when you change the batteries). If the

codes are recorded, you can use the Direct Entry method

to reprogram your remote to control your devices, which is

quick and easy.

1. Press and hold the device

key (TV, SAT•CBL•

STREAM,

DVD•VCR) whose code you

wish to retrieve. The POWER

key turns on. Keep pressing

the device key.

IMPORTANT

Because this remote controls more than one device,

you must ﬁ rst “tell” the remote which device you wish

to operate. That means, if you wish to operate your TV,

you must ﬁ rst press the TV key to put the remote in the

TV Mode. The remote stays in that device mode until

you press a different device key. For example, if your

remote is in TV Mode and you want to operate the DVD

player, you must press the DVD•VCR

key to change

device modes.

Problem: The remote does not operate your device.

• Make sure the remote is in the correct mode by pressing

the corresponding device key (TV, SAT•CBL•STREAM,

DVD•VCR). This tells the remote which device to operate.

• Remove any obstacles between the remote and the device.

Make sure you’re aiming the remote at the device’s IR

sensor.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AA batteries, if necessary

(see the Battery Installation section).

Problem: The remote can’t be programmed to operate

your device.

• If you are testing the remote while programming it, you may

be too far away from the device or at a wrong angle. There

must be an unobstructed path between the remote and the

IR sensor on the device. Move closer and make sure you

point the remote at the device you’re trying to control.

• If you’re using the Direct Entry programming method

to enter the codes for your brand and the unit is still not

functioning properly, try the auto, brand, or manual search

method.

• To control combo units, like TV/VCRs or TV/DVDs, you must

program the individual corresponding device keys to control

each part of the combo unit. Once programmed successfully,

the TV key controls the TV functions, and the

DVD•VCR key

controls the VCR or DVD functions.

• Make sure the batteries are fresh and are properly installed.

Problem: The remote doesn’t perform commands properly.

• Make sure the remote is in the correct mode by pressing

the corresponding device key (TV, SAT•CBL•

STREAM,

DVD•VCR). This tells the remote which device to operate.

• Make sure device is ready (for example, the DVD player has

a disc loaded).

• You may have pressed an invalid key for the mode the remote is

in.

• If you’re trying to enter a channel number directly, try

pressing the OK key after entering the channel number as

this is a requirement of certain models and brands.

VOXX Accessories Corporation (the “Company”) warrants to you the

original retail purchaser of this product that should it, under normal use

and conditions, be proven defective in material or workmanship during

its lifetime while you own it, such defect(s) will be repaired or replaced

(at the Company’s option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the

product is to be delivered with proof of warranty coverage (e.g. dated bill

of sale), speciﬁ cation of defect(s), transportation prepaid, to the Company

at the address shown below.

This Warranty does not cover product purchased, serviced or used

outside the United States or Canada. This Warranty is not transferable

and does not extend to costs incurred for installation, removal or

reinstallation of the product. This Warranty does not apply if in the

Company’s opinion, the product has been damaged through alteration,

improper installation, mishandling, misuse, neglect, accident, or the

simultaneous use of different battery types (e.g. alkaline, standard or

rechargeable).

THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY

IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE

AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE

PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL

BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL

THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES WHATSOEVER. No person or representative is authorized

to assume for the Company any liability other than expressed herein in

connection with the sale of this product.

Some states/provinces do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential

damage so the above limitations or exclusions may not apply to you.

This Warranty gives you speciﬁ c legal rights and you may also have

other rights, which vary from state/province to state/province.

U.S.A.: Audiovox Return Center, 150 Marcus Blvd., Hauppauge, New

York 1 1788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,

Unit 3, Door 16, Mississauga, Ontario L5T 3A5

Trademark(s) ® Registered

RCR314WR US 04

3502 Woodview Trace, Suite 220

Indianapolis, IN 46268

Step 1: Install your batteries

Step 2: Program your remote

Tour of the Remote

Advanced Functions

Troubleshooting

Limited Lifetime Warranty

POWER key

2. If you’re programming the TV or

SAT•CBL•STREAM key, go to step 3.

If you’re programming the

DVD•VCR key, you need

to tell the remote which kind of device you want this

key to control, VCR or DVD.

Press and hold the

DVD•VCR key. While you’re holding

down the DVD•VCR key, use your other hand to press

the number key for the type of device you want to

control with this key: 2 for VCR, 3 for DVD.

3. Press and hold the device key you want to program.

While you’re holding down the device key, use your

other hand to press and hold the remote’s POWER key

at the same time.

Note: All TV codes begin with the number 1; all VCR

and DVR codes begin with the number 2; all DVDs,

the number 3; and all satellite receivers, cable boxes,

streaming players, and DTV converters, the number 5.

5. Repeat step 4 until you have retrieved all ﬁ ve numbers

in the code. After the ﬁ fth number is retrieved, the

POWER key blinks brieﬂ y, then turns off.

TIP: To exit the Code Retrieval Mode at any time, press

the GO BACK key.

Note: If you press an invalid key during the Code

Retrieval process, the remote will not respond. If

you do not press a valid Code Retrieval key (TV,

SAT•CBL•

STREAM, DVD•VCR, INFO-OPTIONS, GO BACK),

Code Retrieval times out after 15 seconds. The POWER

key blinks four times, and then turns off.

CHAN and VOL keys act as channel and volume controllers.

The CHAN keys also provide skip forward and skip back

control for DVD players and DVRs that support this

functionality.

GO BACK exits remote programming; it also performs the

same functions as on your original remotes.

The INPUT and — (dash) key has three functions: (1) it

toggles through all the video sources connected to your TV;

(2) when the remote is in VCR mode, this button toggles

between VCR and the TV input; (3) when you’re entering

digital channel numbers directly, this button lets you

separate the main channel number from the sub-channel

number (such as 59.1).

Backlighting

Backlight illumination helps you see the remote control

keys better in the dark. You can turn backlight illumination

on or off by pressing the

LIGHT key ( ). Backlighting

stays on as long as keys are being pressed and turns off six

seconds after the last keypress. Once the backlight time has

timed out, any keypress will reactivate it. If the backlight

illumination is on, and you press the backlight key, the

backlight turns off.

2. While holding the device key down, press and hold the

INFO-OPTIONS key. The POWER key turns off. After

holding down both keys for three seconds, the

POWER

key turns back on.

3. Release both keys. The

POWER key remains on.

4. Starting with the number 1 key, press and release each

number key on the keypad in the following order: 1-9,

then 0. The number that causes the

POWER key to

blink is the ﬁ rst number of the code. As you ﬁ nd each

number of the code, write it down for future reference.

TIP: Each device key is associated with a type of device—the

TV is preset to search for TVs, SAT•CBL•STREAM for

satellite receivers, cable boxes, digital TV converters, or

streaming media players, and DVD•VCR for VCRs or DVD

players.

The POWER key serves as an indicator light during

programming, giving you feedback at each stage of the

process.

Auto Code Search

The Auto Code Search goes automatically through all the

codes for the device you’re trying to control. When you ﬁ nd

the one that operates your device, you can stop the search

and store that code.

TIPS: Each device key is associated with a type

of device—the TV is preset to search for TVs,

SAT•CBL•STREAM for satellite receivers, cable boxes,

digital TV converters, or streaming media players, and

DVD•VCR for VCRs or DVD players.

To exit without saving a new code at any point in the

Auto Code Search, press the

GO BACK key.

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program.

While you’re holding down the device key, use your

other hand to press and hold the remote’s POWER

key

at the same time.

2. If you’re programming the TV or

SAT•CBL•STREAM key, go to step 3.

If you’re programming the

DVD•VCR key, you need

to tell the remote which kind of device you want this

key to control, VCR or DVD.

Press and hold the

DVD•VCR key. While you’re holding

down the DVD•VCR key, use your other hand to press

the number key for the type of device you want to

control with this key: 2 for VCR, 3 for DVD.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote.

If some device features don’t work, go to next step to

try a different code.

2. Repeat the Auto Code Search Method from the

beginning. When your device turns off, do not stop

searching. Instead, with the unit now off, continue to

press the PLAY key every 5 seconds until the unit turns

back on.

3. Once the unit turns back on, press the REVERSE key

on the remote every 2 seconds until your device turns

off again. When your device turns off again, press the

STOP key.

4. Test the key’s functionality again by attempting to

control a variety of the device’s functions. If the code

that has been stored controls the majority of the

device’s functions, programming is complete. If the

code stored does not give maximum functionality, try

another code.

4. Wait until the POWER key comes on and stays on.

Then release both keys.

5. Point the remote directly at the

front panel of the device you

want to control. Press PLAY on

the remote and wait 5 seconds.

The remote is testing a batch of

10 codes on your device.

Did your device turn off?

YES: Go to step

NO: Press PLAY again. The remote tests the next batch

of 10 codes.

Keep pressing PLAY every 5 seconds until your device

turns off.

6. When your device turns off, press

the REVERSE key on the remote

and wait at least 2 seconds.

The remote tries the last of the

previous ten codes.

Did your device turn on?

YES: Press the STOP key. You’re

done! You’ve programmed this

device key.

NO: Press REVERSE again. The remote tests the next

code in the batch.

Keep pressing REVERSE every 2 seconds until your

device turns back on. When it does, press STOP.

Note: If you accidentally press the REVERSE key after

your device turns on, press the FORWARD key. Then, wait

two seconds to see if your device turns off again.

NOTES

Throughout the programming of each key, be sure to

keep the remote pointed at the IR sensor of the device

you are currently programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

maximum functionality. If some features don’t work, try

a different code. See the “Testing the Code for Maximum

Functionality” section below for more information.

During the Auto Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the

POWER key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The

POWER key blinks four times and turns off when the

remote has gone through all the codes. The remote exits

the Auto Code Search. If your device hasn’t turned off

yet, try a different search method.

Manual Code Search

The Manual Code Search lets you go one-by-one through

all the codes for the device you’re trying to control. When

you ﬁ nd the one that operates your device, you can stop the

search and store that code.

Actual model may vary from

illustration

TIPS: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•STREAM for

satellite receivers, cable boxes, digital TV converters, or

streaming media players, and DVD•VCR for VCRs or DVD

players.

The POWER key serves as an indicator light during

programming, giving you feedback at each stage of the

process.

The Manual Code Search method may take a long time

because the remote searches through all of the codes in

its memory one-by-one. If your brand is listed in the Brand

Codes or the Code Lists, ﬁ rst try the Brand Code Search or

the Direct Code Entry method.

To exit without saving a new code at any point in the

Manual Code Search, press the GO BACK key.

DVD#VCR CODE

DVD VCR

TV CODE

SAT#CBL#STREAM CODE

SAT CABLE DTV CONVERTER

STREAMING PLAYER

previous next

Top Automotive Device Types

Top Automotive Brands

Top Baby Care Device Types

Top Baby Care Brands

Top Car Audio & Video Device Types

Top Car Audio & Video Brands

Top Cellphone Device Types

Top Cellphone Brands

Top Communications Device Types

Top Communications Brands

Top Computer Device Types

Top Computer Brands

Top Fitness Device Types

Top Fitness Brands

Top Home Audio Device Types

Top Home Audio Brands

Top Household Appliance Device Types

Top Household Appliance Brands

Top Kitchen Appliance Device Types

Top Kitchen Appliance Brands

Top Laundry Appliance Device Types

Top Laundry Appliance Brands

Top Lawn & Garden Device Types

Top Lawn & Garden Brands

Top Marine Equipment Device Types

Top Marine Equipment Brands

Top Musical Instrument Device Types

Top Musical Instrument Brands

Top Outdoor Cooking Device Types

Top Outdoor Cooking Brands

Top Personal Care Device Types

Top Personal Care Brands

Top Photography Device Types

Top Photography Brands

Top Portable Media Device Types

Top Portable Media Brands

Top Power Tools Device Types

Top Power Tools Brands

Top TV and Video Device Types

Top TV and Video Brands

Top Videogame Device Types

Top Videogame Brands

RCA RCR313BR Universal Remote User Manual