Filter
Top Products
English - 2
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the “I” button (On/Off) on the front (or side) of the
television.
3 Press the
POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to “Channel - Auto Store” on page 3 or “Channel -
Manual Store” on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
“Setup - Plug & Play” on page 3.
4 To switch the television off, press the “I” button (On/Off)
on the front (or side) of the television.
Switching the Television On and Off
The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
➢
Caution : One pole switch is totally not off(one line
still live) if power cord is not unplugged.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the “
I”
button (On/Off) on the front (or side) of the television.
It is best to unplug the set from the mains and aerial.
Placing the Television in Standby Mode
1 POWER
Used to switch the TV
on and off.
2 Numeric buttons
Used to select channels
directly.
3
-/--
Used to select a channel
numbered ten or over.
Press this button, then
“--” symbol is displayed.
Enter the two-digit
channel number.
4
2
1
/
Used to increase or
decrease the volume.
5 MENU
Used to display the
on-screen menu or
return to the previous
menu.
6 ▲/▼/◄/►
Used to control the
cursor in the menu.
7
S.MENU
Used to display the
sound menu.
8
TURBO
Used to select the turbo
sound option.
9 DUAL I-II
Used to select the sound
mode.
0 SOURCE
Used to display all of the
available video sources.
!
INFO
Used to view the channel
information and setting
status you selected.
@
PRE-CH
Used to switch
repeatedly between
the last two channels
displayed.
#
P /
Used to display the
next or previous stored
channel.
$ EXIT
Used to exit from any
display or return to
normal viewing.
%
MUTE
Used to switch the
sound off temporarily. To
turn the sound back on,
press the MUTE, , or
button.
^ ENTER
While using the
on-screen menus, press
the
ENTER button to
activate (or change) a
particular item.
& S.MODE
Used to select the sound
effect.
* P.MODE
Used to select the
picture effect.
( TV
Used to return to the
TV mode when it is in
external input mode.
) EZ.VIEW
Used to make TV
viewing much easier.
Remote Control
(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
Installing Batteries
Remove the cover. Install two AAA size
batteries, then replace the cover.
When the remote control does not
operate normally, check that the
“+” and “-” ends of the batteries are
inserted correctly or the batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
-54%
AA68-04001A-00Eng_0707.indd 2 2008-07-07 오전 11:54:53