Samsung SV-450X VCR User Manual


 
GB
27
Using the G-CODE Feature
(SV-655B/655X/255B Only)
SPEED DUB TV/VCR TIMER
1
G-CODE
CODE ---------
CODE:0-9 CORRECT:
END:MENU
**
TIMER METHOD
**
STANDARD
G-CODE
➐❷
END:MENU
Before presetting your VCR:
Switch on both the television and your VCR
Check that the date and time are correct
Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1 Press the TIMER button.
Result
: The TIMER METHOD is displayed.
2 Press the corresponding
or
buttons, until the G-CODE option
is selected.
3 Press the
❿☎
button to select G-CODE.
Result
: A message is displayed to allow you to enter the
G-CODE code.
If all six programmes have been set, the message TIMER
IS FULL is displayed. Refer to page 29 if you wish to
cancel a preset recording.
4 Press the numeric buttons to enter the code opposite the pro-
gramme that you wish to record in your television magazine.
If you wish to correct the G-CODE code that you are
entering:
Press the
button until the digit to be corrected is
cleared
Enter the correct digit
5 Press the MENU button.
Result
:
The information concerning the programme is displayed.
When using the G-CODE function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or
buttons. Refer to the following page if:
The programme number or times flash
You wish to modify the programme
6 If the programme and times are correct, press the MENU button.
7 Press the VCR STANDBY/ON (STANDBY/ON) button to activate
the timer.
Result
: The Timer indicator ( ) is displayed.
If no cassette has been inserted when you press
VCR STANDBY/ON (STANDBY/ON) the Timer indicator
flashes. If the safety tab on the cassette has been broken,
the cassette is ejected. Insert the appropriate cassette.
8 Refer to page 29 if you wish to:
Check that your VCR has been programmed correctly
Cancel a preset recording
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to programme
your videorecorder instantly with the remote control. Tap
in the G-CODE code for the programme you wish to
record.
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
V
IPC
+
NICAM
PROG
1/JAN MON 21:28
PR DAY START
STOP
L1 MO 1 12:00
12:50SP
-- ---- --:--
--:----
-- ---- --:--
--:----
-- ---- --:--
--:----
-- ---- --:--
--:----
-- ---- --:--
--:----
➐❷
➛❿
DELETE:CLR/RST MENU
26
Modifying G-CODE Programming
(SV-655B/655X/
SV-255B Only)
If you wish to correct the programme displayed or modify certain elements, such as the recording
speed, you can do so before you press MENU a second time to confirm.
If you wish to... Then...
Select an input source other Press the
or
buttons, until the PR selection flashes.
than the tuner
LINE IN 1 or LINE IN 2 input Press the INPUT button one or more times to change the
input source selection.
The input source must be selected before changing any
other value.
Record a programme every day Press the
or
buttons, until the DAY selection flashes.
(Monday to Sunday) at the same time
Press the
or
buttons, until the DLY (Daily) value is
displayed.
Record a programme every week Press the
or
buttons, until the DAY selection flashes.
on the same day and at the same time
Press the
or
buttons, until the W- (Week) value is
displayed, followed by the required day.
Example
: W-SA (Weekly Saturday)
Extend the recording time Press the
or
buttons, until the STOP selection flashes.
Press the
or
buttons to increase or decrease the stop
time.
Select the recording speed Press the
or
buttons, until the recording speed selection
(SV-640B only) flashes.
Press the
or
buttons until the correct indication is
displayed:
AUTO (Auto Tape Speed Select) : see page 28
SP (Standard Play)
LP (Long Play)