Filter
Top Products
15
Starting setup
The Starting Setup menu appears the first time
you turn on the TV, and assists you to specify the
Air/Cable setting, and program your channels
automatically.
IMPORTANT: Make sure that the antenna or cable
TV system connection is made!
1
To turn on the TV, press
(POWER) (POWER
indicator on the front of the unit changes blue. It
may take approx. 10 seconds for a picture to appear
on screen.). The starting setup function begins.
Automatic Search Start
This unit has been preset to STORE brightness
This setting does not qualify under ENERGY
STAR V4.0. To reduce brightness and energy
consumption, change setting to ‘HOME’. This
setting does qualify under ENERGY STAR V4.0.
Auto Setup
TV Location Store
: Adjust
: Select
Signal Type Cable
2
Press ▲/▼ to select “TV Location”, then press ◀/▶
to select “Store” or “Home”. This product qualifies
for ENERGY STAR V 4.0. In Home mode default
setting.
NOTE:
This unit has been preset to STORE brightness.
This setting does not qualify under ENERGY
STAR V4.0. To reduce brightness and energy
consumption, change setting to ‘HOME’. This
setting does qualify under ENERGY STAR V4.0.
The device may not conform to the ENERGY
STAR V4.0. standard after Reset is performed or
the Backlight is adjusted.
•
•
3
Press ▲ or ▼ to select “Signal Type”, then press
◀ or ▶ to select “Cable” or “Air”.
4
Press ▲ or ▼ to select “Automatic Search”, then
press ▶ or ENTER.
5
Now the “Auto Setup” starts. After the starting
setup is completed, the TV channel appears on
the screen.
•
Depending on the reception condition, it may
take from 15 minutes to 30 minutes to complete
memorizing digital cable channels. Please be patient.
NOTE:
If you press ENTER in the process of “Auto Setup”,
the Starting Setup stops and changes to the normal
screen.
When you make a menu selection, your changes
occur immediately. You do not have to press EXIT to
see your changes.
TV operation
1
To turn on the TV, press
(
POWER).
(POWER indicator on the front of the unit
changes blue. It may take approx. 10 seconds for
a picture to appear on screen.)
2
Adjust the volume level by pressing VOL + or – .
The volume level will be indicated on the screen
by blue bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of blue bars also decreases.
•
•
3
Set the Signal Type option to the appropriate
position (see “Air/Cable selection” on page 18).
4
Press the Direct Channel Selection (0-9, –)
buttons to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to select
channel 2, press 2, then press ENTER.
10-99: Press the 2 digits in order. Example, to
select channel 12, press 1, 2, then press
ENTER.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0, then press
ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
If a channel is selected with only audio content,
“Audio only” will be displayed on the screen.
If a channel is selected with a weak digital
signal, “Digital channel signal strength is low”
will be displayed on the screen.
The same program may be available on either
an analog channel or a digital channel. You may
choose to watch either format.
If a channel is selected to which you have not
subscribed,
“Digital channel is encrypted” will
be displayed on the screen.
•
•
•
VHF/UHF/CABLE CHANNELS
Air Cable
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-135 (100) (135)
01 (4A)
NOTE:
If a channel with no broadcast is selected, the
sound will automatically be muted.
It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press ▲/▼ or corresponding Number
buttons (0-7), then press ENTER. You can select TV,
Video1, Video2, Component, HDMI1, HDMI2, HDMI3
or PC depending on which input jacks you used to
connect your devices.
Input Select
1.Video1
2.Video2
3.Component
4.HDMI1
5.HDMI2
7.PC
6.HDMI3
[0-7]:Select
0.TV
CH /
Press and release CH / . The channel automatically
stops at the next channel set into memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on page 18.
•
•
ENGLISH
3CN0121A_En.indd 153CN0121A_En.indd 15 6/25/10 4:05:58 PM6/25/10 4:05:58 PM