Filter
Top Products
OUTPUT TERMINALS
TAPE END OUT Terminal
X During recording, when the end of the tape is reached
or when the tape counter reading indicates 1 hours 57
minutes or more, the output becomes 0V (Low).
X To reset the output, press the STOP or EJECT button.
X During autorepeat recording, when the end of the tape
is reached, the output becomes 0V (Low) for about 2
seconds only.
TAPE END OUT Terminal Output Setting
1 Press the MENU button until the (SET UP 3) menu is
displayed.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@DURATION@@@20S
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
2 Press the * (or +) button, until the “TAPE END OUT”
setting is flashing.
3 Press the l (or j) button, to select the desired
output mode.
–3M . . . . . . . The output becomes 0 V (Low)
when the tape counter reaches
“1
H
57
M
00
S
” and/or when the tape
reaches the end.
END . . . . . . . The output becomes 0 V (Low)
when the tape reaches the end.
4 Press the SEARCH/AUDIO ON button to save the
setting.
SW OUT Terminal
When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input (SW
IN) of devices like a camera switcher unit, or a quad
compressor.
SW OUT Terminal Output Setting
1 Press the MENU button until the (SET UP 4) menu is
displayed.
ø
The FIELD (or FRAME) setting is flashing.
@@@@@@@<SET@UP@4>
*SW@OUT
@@FIELD@@@@@@@@@01
@@TIMING@@@@@@@@FIELD
@@2H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
NOTE:
X If “TIMING” is set to FRAME (see step 4),
“FRAME” will be indicated instead of “FIELD”.
2 Press the l (or j) button to set the desired pulse
signal interval.
Available settings are:
FIELD. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field
FRAME . . . . 01, 02, 03, 04, 05, 10, 30 or 60 frame
3 Press the * button, until the “TIMING” setting is
flashing.
4 Press the l (or j) button to set “FIELD” or “FRAME”.
FIELD. . . . . . 1 pulse is output after each set
number of fields.
FRAME . . . . 1 pulse is output after each set
number of frames.
5 Press the * button, until the “2H” setting is flashing.
6 Press the l (or j) button to set the desired “2H”
mode.
Y. . . . . . . . . . When recording in 2-hour mode, a
pulse signal is output.
N . . . . . . . . . When recording in 2-hour mode, a
pulse signal is not output.
7 Press the SEARCH/AUDIO ON button to save the
settings.
Tape end or 1
H
57
M
00
S
5V (H)
0V (L)
(Output impedance: 5.7 kΩ)
Output reset
5V (H)
0V (L)
(Output impedance: 5.7 kΩ)
FIELD
FRAME
: 16.7 msec.
: 5 msec.
RC4Q/NA2 (TLS-9072 GB) Thu. Sept., 07/2000
English 33