Filter
Top Products
56
E
Specications
n
Product Specications
Model PN-R703 PN-R603
LCD component
70" Class [69-1/2 inch (176.6cm)
diagonal] TFT LCD
60" Class [60-1/16 inch (152.5cm)
diagonal] TFT LCD
Max. resolution (pixels)
1920 x 1080
Max. colors
Approx. 1.06 billion colors
Pixel pitch
0.802 mm (H) × 0.802 mm (V) 0.692 mm (H) × 0.692 mm (V)
Viewing angle
176° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
60-9/16 x 34-1/16 (1538.9 x 865.6) 52-5/16 x 29-7/16 (1329.1 x 747.6)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω],
DisplayPort 1.1
Sync signal
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*
1
,
Composite sync (TTL: positive/negative)*
1
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV HDMI x 2
Mini D-sub 15 pin, 3 rows x 1
PC DisplayPort x 1
DVI-I 29 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 2
Serial (RS-232C)
D-sub 9 pin x 1
Output terminals PC
DisplayPort x 1
DVI-D 24 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
LAN terminal 10 BASE-T/100 BASE-TX
Speaker output 10 W + 10 W
Power requirement AC 100 - 240 V, 3.0 - 1.2 A, 50/60
Hz
AC 100 - 240 V, 2.3 - 1.0 A,
50/60 Hz
Operating temperature
*
2
32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(Input signal waiting mode
*
3
/ standby mode
*
4
)
270 W (1.4 W / 1.4 W) 200 W (1.4 W / 1.4 W)
Dimensions (excluding protrusions) inch (mm)
Approx. 62-1/8 (W) x 1-9/16 (D) x
36-1/16 (H) (1578 x 39.4 x 916)
Approx. 54-1/4 (W) x 1-9/16 (D) x
31-1/4 (H) (1378 x 39.4 x 794)
Weight lbs. (kg)
Approx. 94.8 (43) Approx. 70.5 (32)
*1 D-Sub input terminal only.
*2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specied by the optional equipments.
*3 When AUTO INPUT CHANGE is set to OFF.
*4 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.