Filter
Top Products
111
Specifications
Appendixes
Video performance
Band width Composite/S-video (DSR-1500A):
30 Hz to 4.2 MHz ±1.0 dB (Y)
Composite/S-video (DSR-1500AP):
25 Hz to 4.8 MHz ±1.0 dB (Y)
Component (DSR-1500A):
30 Hz to 5.0 MHz ±1.0 dB (Y),
30 Hz to 1.5 MHz +1.0/
−
5.0 dB (R
−
Y/
B
−
Y)
Component (DSR-1500AP):
25 Hz to 5.0 MHz ±1.0 dB (Y),
25 Hz to 2.0 MHz +1.0/
−
2.0 dB (R
−
Y/
B
−
Y)
S/N Composite/S-video I/O (Y):
52 dB or more
Component I/O (Y): 55 dB or more
Y/C delay 30 ns or less
K-factor 2.0% or less (K2T, KPB)
Processor adjustment range
Video level* ±3 dB/
−∞
to 3 dB selectable
Chrome level* ±3 dB/
−∞
to 3 dB selectable
Setup/Black level*
±30 IRE (±210 mV)
Chroma phase* ±30°
System phase** Sync: ±1
µ
s
SC: ±180°
* Adjust with menu settings.
** Adjust with controls on the front panel.
Audio performance
Frequency response
Two-channel (48 kHz) mode:
20 Hz to 20 kHz ±1.0 dB
Four-channel (32 kHz) mode:
20 Hz to 14.5 kHz ±1.0 dB
Dynamic range More than 87 dB
Distortion (THD + N)
Less than 0.07% (48 kHz)
Input connectors
Digital signal inputs
SDI/SDTI (QSDI) IN (optional DSBK-1501 Digital Input/
Output Board required)
BNC type
SDTI (QSDI) format (270 Mbps)
SDI format (270 Mbps), SMPTE 259M/
CCIR656-III
AUDIO (AES/EBU) IN (optional DSBK-1501 Digital
Input/Output Board required)
BNC type (×2), complying with AES-
3id-1995
i.DV IN/OUT
6-pin IEEE 1394 connector
Analog video inputs
REF. VIDEO IN
BNC type (×2, loop-through with 75
Ω
automatic terminator)
Black burst
0.286 V (DSR-1500A) or 0.3 V (DSR-
1500AP), 75
Ω
, negative sync
Composite sync
VIDEO IN (optional DSBK-1504/1504P Analog Input
Board required)
BNC type (×3 and 1 loop-through
connector with 75
Ω
automatic
terminator), composite/component/S-
video switchable
Composite
Y/CPST and 1 loop-through connector
with 75
Ω
automatic terminator: 1.0
Vp-p, 75
Ω
, sync negative
Component
Y/CPST: 1.0 Vp-p, 75
Ω
, negative sync
R
−
Y/C and B
−
Y: 0.7 Vp-p (75% color
bars for DSR-1500A or 100% color
bars for DSR-1500AP), 75
Ω
S-video
Y/CPST: 1.0 Vp-p, 75
Ω
, negative sync
R
−
Y/C: 0.286 Vp-p (DSR-1500A) or 0.3
Vp-p (DSR-1500AP), 75
Ω
(burst
level)
Analog audio inputs
AUDIO IN (optional DSBK-1504/1504P Analog Input
Board required)
XLR 3-pin, female (×2), +4/0/
−
3*/
−
6
dBm, high impedance, balanced
* For DSR-1500AP only
Time code input
TC IN
BNC type, SMPTE time code (DSR-
1500A) or EBU time code (DSR-
1500AP), 0.5 Vp-p to 18 Vp-p, 3.3 k
Ω
,
unbalanced