Filter
Top Products
TT128x High Definition Professional Receiver/Decoder
15
4 Menu Structure
Section C.9
Section C.6
Section C.4
Section C.5
4. Conditional Access
Menu
5. TS Output Menu
5.1 Connector 1/2
7. System Menu
2. Input Menu
(QPSK, G.703 or IP or HOM)
1. Presets Menu
TT1280 Initialising
SWITCH ON
Boot Screen
1 Preset Menu
2 Input Menu
3 Service Menu
4 Conditional Access Menu
5 TS Output Menu
6 Alarms Menu
7 Systems Menu
7 Date/Time
7.1 Setup Operating Mode
7.1.1 LCD Contrast
7.1.2 Serial Remote Protocol
7.1.3 IP Address
7.1.3.1 Subnet Mask
7.1.3.2 Gateway Address
7.1.4 Restore System Defaults
7.1.5 Service Hunt Mode
7.1.6 SI Mode
7.1.7 Customisation Key
7.2 IRD Details Electronic Serial No.
7.2.1 Software Version
7.2.1.1 Decoder Version
7.2.3 Hardware Version
7.2.4 PLD Version
7.2.5 Temperature
7.3 System Restart
1 Presets Select
1.1 Presets Save
2.1 Select Input (ASI/SSI)
2.2 SMPTE 310
2.3 G.703 PDH Rate/DS3 Framing Option
2.3.1 G.703 Status
2.3.1.1 Randomisation/Stuffing
2.3.1.2 Signal Status
2.3.2 Reed Solomon
2.3.3 Interleaver
2.3.4 Signal Level
3.1 Video Selection
3.1.1 Resolution/Frame Rate
3.1.2 Coding Mode/Profile
3.1.3 GOP/Pixel/Aspect Ratio
3.1.4 Rate Buffer Level/Bitrate
3.1.5 Fail Mode
3.1.6 Test pattern
3.1.7 Framesync
3.1.7.1 Offset
3.1.8 Video Delay
3.1.9 Output Mode
3.1.10 Trisync Mode
3.1.11 Embedded Audio Channel
3.1.11.1 Embedded Audio PIDs
3.2 Audio 1 Selection
3.2.1 Sampling Rate/Bitrate
3.2.2 Rate Buffer Level
3.2.3 Delay Adjustment
3.2.4 Digital Output/Routing
3.2.5 Clipping Level
3.2.6 AC3 Downmix Method
3.3 Audio 2 Selection
3.3.1 Sampling Rate/Bitrate
3.3.2 Rate Buffer Level
3.3.3 Delay Adjustment
3.3.4 Digital Output/Routing
3.3.5 Clipping Level
3.3.6 AC3 Downmix Method
3.5 Async Data Selection
3.4.1 Bitrate/Status
3.6 Sync Data Selection
3.5.1 Bitrate/Status
3.7 Ethernet Data
3.6.1 Bitrate/Status
3.6.2 Diagnostics
3.6.3 Gateway Setup
3.8 VBI Selection
3.7.1 VITC Insertion
3.7.2 Closed Caps
3.9 PCR Selection
3.10 Network ID/Original Network
3. Service Selection Menu
4.1 RAS Mode/RAS Key Setup
4.2 Signal Protection Status
4.3 Common Interface Status/Director Status
1
4.4 BISS Mode/Key Setup
4.4.1 BISS User ID One Setup
4.4.2 BISS User ID Two Setup
Section C.8
6. Alarms Menu
6.1 Transport Stream alarm setup
6.2 Video alarm setup
6.3 Audio 1 alarm setup
6.4 Audio 2 alarm setup
6.5 MER alarm setup
6.6 BER alarm setup
6.7 Temperature alarm setup
Section C.7
1
Dependent on model type
3.1.6.1 Test Pattern Standard
3.4 Dolby Selection
7.2.6 Model Number
7.2.2 Firmware Version
Figure 4.1: Menu Structure