Filter
Top Products
12
Connections (Continued)
Basic TV Connections
Make one of the following connections, depending on
the capabilities of your existing equipment.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note:
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
1.When the DVD+VCR is turned off,
press and hold
REW m or FWD M on the front panel for about
five seconds.
It will turn itself on and “RF03” or “RF04” appears in the dis-
play window.
2.
Press REW m or FWD M on the front panel or
CH/TRK (+/-) on the remote control to change the RF
output channel (CH 03 or CH 04).
3.
Turn off and on the DVD+VCR.
4.
Press the TV CH to 3 or 4 depending on the RF
output channel you had selected.
Now you can watch the DVD+VCR playback on CH3
or CH4 of your TV.
Audio/Video connection
11
Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
22
Connect the Left and Right DVD/VCR AUDIO OUT
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
Notes:
If you use this connection, set the TV’s source selector to
VIDEO.
For DVD/VCR VIDEO OUT jack connection, resolution must
be set to 480i or 480p by pressing RESOLUTION on the
front panel, however DVD/VCR VIDEO OUT is always at
480i standard resolution.
HDMI mode must be set to OFF for DVD/VCR VIDEO OUT
jack connection.
Optional, Preferred TV Connections
Note:
You can ONLY watch and listen to DVD playback
through the connections shown below.
S-Video connection
11
Connect the S-VIDEO OUT jack on the DVD+VCR
to the S-Video in jack on the TV using the optional
S-Video cable (S) (not supplied).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
Notes:
For S-Video connection, resolution must be set to 480i or
480p by pressing RESOLUTION on the front panel, however
S-VIDEO OUT is always at 480i standard resolution.
HDMI mode must be set to OFF for S-Video connection.
Component Video (Color Stream
®
) / Progressive
Scan (ColorStream
®
pro) connection
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan for-
mat, the picture will appear scrambled if you try
Progressive Scan on the DVD+VCR.
11
Connect the COMPONENT / PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using the optional
Y Pb Pr cables (C) (not supplied).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Notes :
You can change the resolution (480i, 480p, 720p, 1080i) for
the component/progressive scan video output by pressing
RESOLUTION on the front panel.
For 720p and 1080i resolution, only non-copy protected
discs can be played back. If the disc is copy protected, it will
be auto down-scaling to 480p resolution.
HDMI mode must be set to OFF for Component video con-
nections.
L
R
AUDIO INPUT
VIDEO
INPUT
ANTENNA
INPUT
Rear of TV
Rear of DVD+VCR
A1 VR
Y
Pb
Pr
COMPONENT VIDEO INPUT
L
R
AUDIO INPUT
S-VIDEO
INPUT
Rear of TV
Rear of DVD+VCR
S
A2
C