Filter
Top Products
Tuning Antenna
STEP 1. Your receiver should indicate it is receiving a signal. To tune
your antenna for the best signal strength. SLOWLY move the antenna
left, then right, until you have found the position that gives the highest
signal strength. It is important to turn the antenna slowly. Because
the signal is digital, the receiver takes a few seconds to lock on.
STEP 2. Place rotation clamp in the LOCK position. This prevents
antenna movement and loss of signal.
STEP 3. SLOWLY raise, then lower the antenna until you have peaked
the signal. You are now ready to watch satellite TV!
Lowering Antenna to Travel Position
STEP 1. Set rotation clamp to ROTATE position.
STEP 2. Rotate antenna until pointer on directional handle aligns with the
red screw on the rotation clamp.
STEP 3. Turn elevating crank counter clockwise in direction of DOWN
arrow until meeting resistance. The number of turns will vary according
to the elevation angle the antenna was set at.
STEP 4. Move rotation clamp to the LOCK position. Antenna is now
locked in travel position.
STEP 5. Snap elevation crank in place.
CAUTION! NEVER LOWER ANTENNA IN ANY POSITION
EXCEPT TRAVEL POSITION!
DO’S
1. Do check parking location for obstructions before raising antenna.
2. Do carefully raise, lower and rotate antenna. If difcult, check for cause.
3. Do rotate SLOWLY when searching for the satellite(s), and check ne tuning on TV
set to make sure it is properly adjusted.
4. Do lower antenna before moving vehicle!
5. Activate programming by calling program provider for your receiver.
1. Don’t move RV/coach with the antenna in the UP position. This will VOID your
WARRANTY. This may also cause damage to your roof.
2. Don’t force elevating crank up or down. Check for cause of trouble.
3. Don’t rotate directional handle hard against stops.
4. Don’t apply paint over top of base plate or any where on lift.
5. Don’t apply sealant on gear housing.
DON’T’S
2
3
300
310
320
330
340
350
50
20
30
40
POINT NORTH
290
10
60
70
240
250
DIRECTIONAL
HANDLE
RED SCREW
ELEVATIING CRANK
DIRECTIONAL HANDLE
POINTER
DIRECTIONAL DIAL
ROTATION CLAMP
FIGURE 1
STEP 1. The more accurately you determine North, the easier it is to locate the satellite.
Step outside and away from your vehicle. (Standing to near your vehicle can give incorrect
compass readings.) It is helpful if there is a landmark on the horizon to represent North. Return
to the vehicle and point the Directional Dial North, or to the landmark.
STEP 2. Turn on receiver and television. Tune the television to channel 3 or 4. Using your receiver manual for in-
structions, go to the Signal Meter screen. Enter nearest Zip code for your location using receiver’s remote control.
After the Zip code is entered, the receiver will indicate numbers for Azimuth (compass heading) and Elevation.
See chart below to determine number of turns needed for each elevation. Turn the elevation handle CLOCKWISE
to raise the antenna. Turn the elevation handle COUNTERCLOCKWISE to lower the antenna.
STEP 3. Press button on Winegard Digital Display Wall plate. If antenna is in travel position, the display will show
LL for Low Limit. HL for High Limit will appear when dish is in up position.
STEP 4. Crank elevation handle to raise antenna. Stop cranking when readout displays correct elevation for your
location, found on the receiver’s signal meter screen.
STEP 5. Rotate antenna VERY SLOWLY until correct satellite signal is acquired. NOTE: Rotate 3°, then stop. DO
NOT rotate continuously, even if you are rotating slowly. If you notice the elevation angle has changed, it could be
due to the following reasons:
1. RV is not parked level.
2. Antenna system is mounted to a slightly sloped RV roof. (This is not a problem. When you have
rotated the antenna so it is facing in approximately the right azimuth [compass direction], simply
adjust to correct elevation and continue searching for signal.
Special Notes: When you have detected the satellite signal, adjust the antenna up/down and left/right for the
strongest signal the receiver displays. Due to variations in receivers and installation methods, you may nd the
elevation numbers, after peaking on the strongest signal, no longer match what the receiver recommended. This
is normal. The elevation sensor should always get you close enough to pick up a signal to peak on. If the display
turns off while you’re searching, just push button for another minute of operation. After a little practice, most peo-
ple nd the signal in 30 to 50 seconds.
Replacement Parts
Repair parts are available at many RV dealers and/or service centers throughout the country. If you don’t have a
dealer/service center near you, call Winegard Company at 1-800-288-8094. All major credit cards accepted.
To order receivers or programming please call
the Winegard receiver hotline: 1-(866) 609-9374
!
Operation