Filter
Top Products
Raising the Antenna
1. Press and hold “POWER” for two seconds to turn on the interface
box. Wait until the interface box finishes “connecting to antenna.” The
TRAV’LER
®
antenna may enter the search routine after ten seconds.
Pay attention to the pinch points as the antenna raises!
2. Wait until the antenna has at least raised to a position in which the feed
arm is parallel to the roof. Then, press “POWER” and “SELECT” at the
same time. The antenna should stop moving.
3. Unplug the interface box. Continue with instructions for your model of
replacement LNB.
Model RP-SK01 DISH
®
1000 Replacement LNB
1. Remove and set aside the two screws from the wider end of the
underside of the integrated adapter.
2. Carefully slide the LNB out from
the integrated adapter. Disconnect
the three cables from the LNB
using a
7
/
16
” wrench.
3. Connect the three cables running
through the integrated adapter
to ports 1–3 (in any order) on the
replacement LNB. Tighten each
cable until fingertight, and then use
a
7
/
16
” wrench to tighten a quarter
turn more.
4. Slide the LNB into the integrated adapter, and re-install the two
screws (removed earlier) through the integrated adapter and LNB.
Model RP-SK05 DIRECTV
®
Slimline Repl. LNB
1. Remove and set aside the four
nuts and bolts holding the LNB
guard to the feed arm. Then, slide
the LNB guard down the feed arm
and toward the reflector.
2. Remove and set aside the two screws
holding the LNB to the feed arm.
3. Carefully slide the LNB out from the feed arm. Disconnect the four
coax cables from the LNB using a
7
/
16
” wrench.
4. Connect the four coax cables running through the feed arm to the
replacement LNB. The coax cables can be connected in any order.
Tighten the cables until fingertight, and then use a
7
/
16
” wrench to
tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws
(removed earlier) through the underside of the feed arm and
replacement LNB. Tighten.
6. Slide the LNB guard up the feed arm and over the LNB. The front of
the LNB guard should be ~½″ in front of the LNB and should not be
touching the LNB. Install the four bolts through the four holes in the
LNB guard. Thread a nut onto each bolt, and tighten.
Model RP-SK09 DIRECTV SWM Slimline Repl. LNB
1. Remove and set aside the four
nuts and bolts holding the LNB
guard to the feed arm. Then, slide
the LNB guard down the feed
arm and toward the reflector.
2. Remove and set aside the two
screws holding the LNB to the
feed arm.
3. Carefully slide the LNB out from the
feed arm. Disconnect the coax cable
from the LNB using a
7
/
16
” wrench.
4. Connect the coax cable running through the feed arm to the
replacement LNB. Tighten the cable until fingertight, and then use a
7
/
16
” wrench to tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws
(removed earlier) through the underside of the feed arm and
replacement LNB. Tighten.
6. Slide the LNB guard up the feed arm and over the LNB. The front of
the LNB guard should be ~½″ in front of the LNB and should not be
touching the LNB. Install the four bolts through the four holes in the
LNB guard. Thread a nut onto each bolt, and tighten.
Screws removed
from integrated adapter
LNB slid out from
integrated adapter
Screws holding
LNB to feed arm
Bolts holding
LNB guard
to feed arm
LNB guard
Integrated
adapter
Bolts holding
LNB guard
to feed arm
Feed arm
Screws holding
LNB to feed arm
Front of
LNB guard