Filter
Top Products
RQT6797
9
Basic play
[DVD-A] [DVD-V] [VCD] [CD] [MP3]
Preparation
Turn on the other equipment (amplifier, television, etc.) and select the
audio/video input to suit the connections to this player.
[1]
Press [POWER Í/I] to turn on the unit.
[2]
Press [OPEN/CLOSE] to open the disc tray.
[3]
Place the disc on the disc tray.
[4]
Press [1] (PLAY).
The disc tray closes and play begins.
Group and track names (MP3) or title and artist names (CD-text) are
displayed on the television. Press [SUBTITLE] to turn the display on
or off.
To stop play
Press [∫] (➡ right, Resume function).
To pause play
Press [;].
Press [1] (PLAY) to restart play.
∫ Auto standby
The unit switches to standby mode after about 30 minutes in the stop
mode.
[Note]
≥If “$” appears on the television
The operation is prohibited by the unit or disc.
≥Discs continue to rotate while menus are displayed even after playing an
item. Press [∫] when you finish to preserve the unit’s motor and your
television screen.
≥Volume may be lower when playing DVDs than when playing other discs
or during television broadcasts. Reduce the volume before playing other
sources so that a sudden increase in output does not occur.
[DVD-A] [DVD-V] [VCD]
Press the numbered buttons to select an item.
To select a 2-digit number
e.g. 23: [S10] ➡ [2] ➡ [3]
≥When playing DVDs, you can also use [3, 4, 2, 1] to select items.
Press [ENTER] to confirm your selection.
Play of the selected item now begins.
Other buttons used to operate menus
Read the disc’s instructions for further details about operation.
[9], [5/9]: Shows the next menu.
[:], [:/6]: Shows the previous menu. [VCD]
[RETURN]: Shows the menu screen.
[TOP MENU]: Shows the first menu screen. [DVD-A] [DVD-V]
[MENU]: Shows the menu screen. [DVD-V]
[DVD-A] [DVD-V] [VCD] [CD] [MP3]
(When the elapsed play time is displayed)
The position you stopped play at is recorded by the unit when “!” is
flashing on the display.
While “!” is flashing, press [1] (PLAY) to start play from where you
stopped it. (When playing DVD-Video ➡ Chapter Review below)
≥The position is cleared when the disc tray is opened or the unit is
switched to standby.
To clear the position
Press [∫] before recalling the memorized position.
This function allows you to memorize a position to start from even after
switching the unit to standby or changing discs. You can memorize
positions on up to five different discs at a time. When you memorize
another position, the earliest position is replaced.
≥This function does not work while playing some DVDs.
1. During play, press [POS. MEMO].
2. Press [POWER Í/I] to switch the unit to standby, or press [OPEN/
CLOSE] to remove the disc.
3. When you are ready to play the disc again, press [1] (PLAY).
Play starts from the memorized position and the position is cleared.
(When playing DVD-Video ➡ Chapter Review below)
To clear the position
Press [∫] before recalling the memorized position.
The following message appears immediately after you press [1] (PLAY).
Press [1] (PLAY) while the message is
displayed and the beginning portions of
each chapter up to the current one are
played. Full play resumes from the point
where you pressed [∫] or [POS. MEMO].
(This feature works only within a title.)
If you do not press [1] (PLAY), the message disappears and play starts
from where you pressed [∫] or [POS. MEMO].
1
2
4
:/6, 5/9
∫
;
1 3
2 4
Numbered
buttons
Label-up (With double-sided discs, load
so the label for the side you want to play is
facing up.)
When a menu screen appears on the television
Resume function
Position Memory function
Chapter Review
[DVD-V]
D.MIX
C DBM
PG
RMTR
TTL
GRP
TRCK
CHAP
D.N.R.
DVD-
A
VR
CD
WMA
MP3
A.ONLY
PROG. SLEEP
A B RNDPGM
A
Position memorized
Light as you memorize positions.
Press PLAY to Chapter Review