Filter
Top Products
12 Projection TV
Installation
Send the TV’s audio to external audio equipment (stereo system) via
the Digital Audio Optical Output port.
How to connect
1. Connect one end of an optical cable to the TV Digital Audio Optical
Output port.
2. Connect the other end of the optical cable to the digital audio optical
input on the audio equipment.
3. Set the TV Speaker option to - “Off”, see the AUDIO menu. Refer
to page 19.
See the external audio equipment instruction manual for operation.
Caution: Do not look into the optical output port. Looking
at the laser beam may damage your vision.
Digital
Digital
Audio Output
Audio Output
- This TV can receive Digital Over-the-air/Cable signals
without an external digital set-top box. However, if you do
receive Digital signals from a digital set-top box or other
digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents
Protection) protocol for DTV (480p,720p,1080i) modes.
How to connect
Use the TV’s COMPONENT (Y, P
B, PR) INPUT or DVI
inputs for video connections, depending on your set-top
box connection options. Then, make the corresponding
audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
2. Use tv/video or comp/dvi on the remote control to
select Component 1, Component 2, or DVI source.
HDSTB Setup
HDSTB Setup
C
A
L
I
B
R
A
T
I
O
N
DIGITAL
AUDIO OUTPUT
OPTICAL
VIDEO L R
ANTENNA1 ANTENNA 2
DVI
-HDTV
INPUT
DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)
DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)
PR
S1
S2
COMPONENT1
A
U
D
I
O
A
U
D
I
O
V
A
R
I
A
B
L
E
A
U
D
I
O
V
I
D
E
O
V
I
D
E
O
I
N
4
(480i/480p/720p/1080i)
COMPONENT2
S-VIDEO
INPUT
P
B
Y
L
L
R
L
R
R
MONITOR
OUTPUT
CENTER
SPEAKER
MODE INPUT
I
N
2
I
N
1
PR
PB
Y
L
R
AUDIO
MONO
B
R
(R) AUDIO (L)
DVI-DTV OUTPUT
DIGITAL AUDIO
OPTICAL
Digital Set-top Box
or
C
A
L
I
B
R
A
T
I
O
N
DIGITAL
AUDIO OUTPUT
OPTICAL
DVI
-HDTV
INPUT
DIGITAL
AUDIO INPUT1
OPTICAL
(COMPONENT1)
DIGITAL
AUDIO INPUT2
OPTICAL
(DVI)
You have to connect the external equipment to select the input source with the tv/video, or comp/dvi button on the
remote control. (You can select every input source with front button though your TV disconnect to an external
equipment.)
EZ Notice: Make
EZ Notice: Make
A/V Connection
A/V Connection
How to connect
1. Connect the Dolby Digital Output jacks from the TV to the input jacks on the
Dolby Digital Receiver.
2. Set up your Dolby Digital Receiver according to the directions provided with
that device.
3. If you wish to use your TV as the “Center channel” for your home theater,
re-direct the center channel to Center speaker mode input jack on the TV.
Set the TV Speaker option to - “Center Speaker ” on the AUDIO menu. Refer
to page 19.
Dolby Digital
Dolby Digital
Audio Connection
Audio Connection
Dolby Digital A/V Receiver
Center Channel
Preamp
Out
Front Left
Front Right
Rear Left
Surround
Rear Right
Surround
Powered
Subwoofer