18
English
Viewing 3D images
You can enjoy viewing 3D images with contents or
programmes corresponding to the 3D effect by wearing
the 3D Eyewear (supplied).
●
The 3D Eyewear must be worn to view 3D images.
●
This TV supports [Frame Sequential]
*
, [Side by Side]
and [Top and Bottom] 3D formats. (3D content of 4K
format is not supported.)
●
For more information, refer to [eHELP] (Watching >
3D).
*
: The 3D format that the images for the left and right
eyes are recorded with the high definition quality and
alternately played back.
3D Eyewear
Use the supplied 3D Eyewear or Panasonic 3D Eyewear
that supports Bluetooth wireless technology.
Note
●
Do not exert pressure on or scratch the lens of the 3D
Eyewear.
●
Do not use devices such as mobile phones
or personal transceivers that emit strong
electromagnetic waves near the 3D Eyewear as this
may cause the 3D Eyewear to malfunction.
●
Do not wear the 3D Eyewear when watching anything
other than 3D images. Liquid crystal displays (such as
computer screens, digital clocks or calculators, etc.)
may be difficult to see while wearing the 3D Eyewear.
First registration
Perform the first registration when first using the 3D
Eyewear with this TV.
1 Turn the TV on
2 Press Power button for about 1 second to turn the
3D Eyewear on
●
The lamp lights for about 2 seconds and then
flashes.
●
The 3D Eyewear will be turned on and start
registration.
●
Place the 3D Eyewear within 50 cm from the TV
while registration in progress.
3 After the registration is successfully completed,
the 3D Eyewear will reconnect with TV
automatically when the 3D Eyewear is turned on
near the TV in 3D mode
Registration again
When connection with the registered TV fails, or when
using with another TV, re-register the 3D Eyewear.
1 Turn the TV on
2 Within 50 cm from the TV, press Power button until
lamp lights, then release it to start registration
3 After the registration is successfully completed, the 3D
Eyewear will reconnect with TV automatically when the
3D Eyewear is turned on near the TV in 3D mode
To view the 3D images
■ Playing back 3D-compatible Blu-ray disc
(Frame Sequential format)
●
Connect the 3D-compatible player via a fully
wired HDMI compliant cable. (If you use the non
3D-compatible player, the images will be displayed in
2D mode.)
●
If the input mode is not switched automatically, select
the input mode connected to the player using the AV
button.
■ 3D-supported broadcast
●
Please consult the suppliers of contents or
programmes for availability of this service.
■ 3D photos and 3D videos taken by
3D-compatible Panasonic products
●
Available in Media Player and Network services.
■ 2D images converted to 3D
●
Press the 3D button and set to [2D→3D] mode in [3D
Mode Selection]. (Contents of 4K format cannot be
changed to 3D mode.)
Preparations
Ensure that the registration of the 3D Eyewear has been
completed.
1 Turn the 3D Eyewear on and put it on
Connection status and battery status are displayed on
the bottom right of the screen.
2 View the 3D images
Safety precautions will be displayed when you first
watch the 3D image. Select [Yes] or [No] to continue to
view 3D images.
Note
●
Turn off the 3D Eyewear after using it.
●
You cannot view the 3D images with the 3D Eyewear
too far from the TV, because of the difficulty of
receiving radio waves from the TV.
●
The range may be shortened depending on the
obstacles between the TV and the 3D Eyewear, or the
surrounding environment.
●
Use the 3D Eyewear where there is no interference
from other Bluetooth devices.
●
3D content will not be correctly visible if the 3D
Eyewear is worn upside down or back-to-front.
●
When viewing 3D images, make sure your eyes
are at an approximately horizontal level and keep a
position where you do not see double images.
●
If light appears to flicker under fluorescents or
dimmers when using the 3D Eyewear, change the
setting of [3D Refresh Rate] in [3D Settings] (Picture
Menu).
●
There are differences in the viewing range of the 3D
Eyewear among individuals.
