FUNAI DVD3315V DVD VCR Combo User Manual


 
EN
22
RECORDING
EN
Satellite Link
You can set the unit to start recording whenever it detects
a video signal from the external tuner.
Preparing for the Satellite Link:
• Only L1 (rear) is available for satellite link and be sure
that this L1 needs to be connected by the external tuner.
• The external tuner should be equipped with some kind
of timer function. Using timer function of the tuner, set it
to the output audio/video signals when it comes to the
time you want to start recording, and stop those signals
when it comes to the time you want to finish recording.
Refer to the tuner’s manual on how to set the timer.
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD VCR
DVD/VC R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO I N
VIDEO IN
AUDIO OUT
VIDEO OUT
L
LY
R
R
C
B
C
R
VCR
AUDIO IN
VIDEO IN
To video out jack
L1
external tuner
To audio(L)out jack
RCA audio/video cables
VHSVHS
VHS
VHS
VHS
Press
VCR
first.
1
Press
SPEED
to select the desired tape speed.
SP
2
In the stop mode, press
SETUP
.
3
Use / to select
“SATELLITE LINK”. Then, press
to go to the next step.
- M E N U -
TIMER PROGRAMMING
B SATELLITE LINK
AUTO REPEAT [OFF]
CLOCK SET
LANGUAGE SELECT
4
Use / to select the
desired hour. Then, press
to
go to the next step.
SATELLITE LINK
0 1 : 0 0 PM
Then, repeat procedures above to select the minute
as well.
The hour can be selected from 1-12 with AM or PM.
When the external tuner signal is stopped, recording
will be stopped.
5
Press to set satellite
link standby mode.
SATELLITE LINK
0 1 : 3 0 PM
[ON]
[TIMER REC] indicator: lights up and the unit goes to
the DVD mode. If you do not use DVD function, turn
OFF the unit.
An external tuner must be turned ON for satellite link
to start. If external tuner is not set to output signals,
satellite link will remain in standby mode.
To Cancel the Satellite Link on Standby:To Cancel the Satellite Link on Standby:
Press [TIMER SET] on the remote control or
[STOP/EJECT C A] on this unit.
To Cancel the Satellite Link in Progress:To Cancel the Satellite Link in Progress:
Press [STOP/EJECT C A] on this unit.
Note:
Recording picture will be distorted if the copy
protection signal is being detected during
satellite link.
When the timer recording and the satellite link
are overlapped, those recordings are recorded as
illustrated below.
e.g.) In case of the satellite link is overlapped on the exist-
ing timer recording.
timer recording
recording result
satellite link
e.g.) In case of the timer recording is programmed in the
middle of the satellite link.
timer recording
recording result
satellite link
e.g.) In case of the timer recording is overlapped on the
existing satellite link.
timer recording
recording result
satellite link
Dubbing a Cassette Tape
Warning: Unauthorized recordings of copyrighted
cassette tapes may be an infringement of
copyright laws.
AUDIO
STANDBY-ON
R
VIDEO
AUDIO OUT
L
R
VIDEO OUT
or
output jacks of
external device
RCA audio cable
RCA video cable
front of the unit
L2
You can use a video disc player, cable/satellite box or
other devices with the audio/video output jacks.
VHSVHS
VHS
VHS
VHS
Press
VCR
first.
1) Press [SPEED] on the remote control to select recording
speed (SP or SLP).
2) Press [INPUT] on the remote control to select L1 or L2
whichever the jack the external device is connected to.
3) Press [RECORD] on the unit, and then start playback of
the external device.
4) To stop recording, press [STOP/EJECT C A] on this
unit.
5) Stop playback of the external device.
Note:
For best results during dubbing, use buttons on
this unit whenever possible. The remote control
might affect another device’s operation.