Filter
Top Products
57
ENGLISH
Searching for digital terrestrial
TV channels automatically
1 Open the menu with »MENU«.
2 Select the line »SOURCE SETUP« with »
V
«
or »
Λ
« and press »OK« to confirm.
– The »SOURCE SETUP« menu appears.
3 Select the line »Source« with »
V
«
or »
Λ
« and press »OK« to confirm.
Select the option »Air« with »
<
«, »
>
«, »
V
« or
»
Λ
« and press »OK« to confirm.
Caution:
7
The antenna power supply (line »Active
Antenna Power«) may only be switched on
if the antenna is an active indoor antenna
with a signal amplifier and it is not already
supplied with a voltage via a mains plug
(or similar supply). Otherwise you may
cause a short circuit and irreparably dam-
age your antenna.
4 Select the »Active Antenna Power« with »
V
«
or »
Λ
«. Switch on the antenna power supply
for the antenna with »
<
« or »
>
« (»On«).
5 Select the line »Automatic Channel Search«
with »
V
« or »
Λ
« and press »OK« to con-
firm.
– The menu appears.
6 Select the line »Country« with »
V
« or »
Λ
«
and press »OK« to confirm. In the country
selection menu, select the country with »
<
«,
»
>
«, »
V
« or »
Λ
« and press »OK« to confirm.
7 Select the line »Scan Typ« with »
V
« or »
Λ
«
and set the option »DTV« with »
<
« or »
>
«.
8 Start the scan with »
« (red).
– All channel and favourites lists will be
deleted and compiled anew.
Note:
7
After starting the scan, a security query will
appear. Press »
« (green) to confirm the
option »Yes«.
– The »Reults« menu appears, and the scan
for TV channels begins. Depending on the
number of television channels received,
this can easily take a few minutes.
– The scan is complete as soon as the
»PROGRAM TABLE« appears.
SPECIAL SETTINGS
----------------------------------------------------------------------------------------------------------
Note:
7
You can abort the search by pressing
»MENU«.
9 Press »MENU« to end the setting.
Searching for digital terrestrial
TV channels manually
1 Open the menu with »MENU«.
2 Select the line »SOURCE SETUP« with »
V
«
or »
Λ
« and press »OK« to confirm.
– The »SOURCE SETUP« menu appears.
3 Select the line »Source« with »
V
« or »
Λ
«
and press »OK« to confirm.
Select the option »Air« with »
<
«, »
>
«, »
V
« or
»
Λ
« and press »OK« to confirm.
Caution:
7
The antenna power supply (line »Active
Antenna Power«) may only be switched on
if the antenna is an active indoor antenna
with a signal amplifier and it is not already
supplied with a voltage via a mains plug
(or similar supply). Otherwise you may
cause a short circuit and irreparably dam-
age your antenna.
4 Select the »Active Antenna Power«« with »
V
«
or »
Λ
«. Switch on the antenna power supply
for the antenna with »
<
« or »
>
« (»On«).
5 Select » Digital Manual Tuning« with »
V
« or
»
Λ
« and press »OK« to confirm.
– The menu appears.
6
Enter the channel number directly with
»
1 ... 0« and press
»OK«
to confirm.
– After the search is complete, the channels
found are displayed in the »Results« menu.
7 Press »MENU« to finish the setting.