Filter
Top Products
POW
ER
TV
VCR
C
B
L
D
VD
1
2
4
5
6
3
7
8
9
0
IN
F
O
S
LE
EP
A
/V
N
ET
E
XI
T
MENU
CH
VO
L
MUTE
PIP PIP C
H
S
W
AP
FR
EE
ZE
PI
P
MO
D
E
PIP A
C
C
E
S
S
V
I
DEO
S
OURC
E
W
IZ
ARD
R
E
C
S
E
LECT
TV/
RG
B
A
S
PE
C
T
STB
AN
T
L
A
S
T
C
H
V
C
R
PL
US
+
S
VC
S
G
U
I
D
E
/
T
V
S
C
H
D
V
I
D
1
V
I
D
2
V
ID
3
V
I
D
4
V
ID
5
TA
P
E
CD
A
MP
M
OD
E
CLU-5723
T
S
I
36
THE REMOTE CONTROL
USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS
Operating the precoded function for your cable box.
This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote command set
of your cable box (refer to page 41).
1. Turn ON your cable box.
2. Aim the remote control at the front of your cable box.
3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode.
4. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 41.
The CBL button light will flash 3 times if the code was accepted.
5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box if the correct two digit pre-
set code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try
a different two digit preset code.
6. The remote will now control your Cable box.
NOTES:
1. If your cable box cannot be operated after performing the
above procedures, your cable box code has not been
precoded into the remote.
2. In the unlikely event that your cable box cannot be
operated after performing the above procedures, please
consult your cable box operating guide.
3. The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
4. The LAST CH button will act as the cable box ENTER
button if required.
5. The SLEEP button will act as your cable box ‘100’ button
if required.
6. The ANT button will act as the TV/STB button when in
STB mode.
ቢ CABLE (CBL) button
This button allows the remote to control your cable box by
setting it to CABLE mode.
ባ PRECODED CABLE BOX buttons
These buttons transmit the chosen precoded cable codes.
ቤ EXCLUSIVE TV buttons
These buttons are for operating the TV.
ቤ
ቢ
ባ
ባ
ቤ
ቤ
ባ
ቤ
ቤ
POWER
TV
VCR
CBL
DVD
1
2
4
56
3
7
89
0
INFOSLEEP
A/V NET
EXIT
MENU
CHVOL
MUTE
PIP SURF
SWAP
FREEZE
PIP MODE
PIP ACCESS
DAY/NIGHT
SOURCE WIZARD
REC
SELECT
TV/RGB
ASPECT
STB
ANT
LAST CH
VID 1
VID 2
VID 3
VID 4
VID 5
PVR
CD
AMP
VIDEO
MY CABLE BOX CODE IS:
NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.