Filter
Top Products
POWE
R
TV
V
CR
C
BL
DVD
1
2
4
5
6
3
7
89
0
INFO
SLEEP
A/V N
E
T
EXIT
M
ENU
C
HVOL
M
U
T
E
P
I
P
P
I
P
C
H
SWA
P
FR
E
EZE
PIP MODE
PIP A
C
CESS
VIDEO
SOURCE WI
Z
ARD
REC
S
ELECT
T
V/RGB
ASPECT
S
TB
ANT
LA
S
T C
H
VC
R PL
U
S
+
S
V
C
S
G
U
I
D
E
/
T
V
S
CH
D
V
I
D
1
V
ID 2
V
I
D
3
V
I
D
4
VID
5
TA
P
E
C
D
A
MP
MODE
C
L
U-5723
TS
I
37
USING THE REMOTE TO CONTROL
SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS
Operating the precoded function for your set-top-box/satellite receiver.
This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the
remote command set of your set-top-box/satellite systems (refer to page 40).
1. Turn ON your set-top-box/satellite systems.
2. Aim the remote control at the front of your set-top-box/satellite systems.
3. Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.
4. Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as
shown on page 40. The STB button light will flash 3 times if the code was accepted.
5. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satel-
lite receiver if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top-
box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.
6. The remote will now control your set-top-box/satellite receiver.
NOTES:
1. If your set-top-box/satellite receiver cannot be operated
after performing the above procedures, your set-top-
box/satellite receiver code has not been precoded into the
remote.
2. In the unlikely event that your set-top-box/satellite
receiver cannot be operated after performing the above
procedures, please consult your set-top-box/satellite
receiver operating guide.
3. The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
4. The ANT button will act as the TV/STB button when in
STB mode.
ቢ SET-TOP-BOX (STB) button
This button allows the remote to control your satellite receiv-
er by setting it to SET-TOP-BOX/SATELLITE mode.
ባ PRECODED SET-TOP-BOX/SATELLITE RECEIVER but-
tons
These buttons transmit the chosen precoded set-top-
box/satellite codes.
ቤ EXCLUSIVE TV buttons
These buttons are for operating the TV.
ባ
ባ
ቤ
ባ
ባ
ቤ
ቤ
ባ
ቤ
ባ
ቤ
ቢ
POWER
TV
VCR
CBL
DVD
1
2
4
56
3
7
89
0
INFOSLEEP
A/V NET
EXIT
MENU
CHVOL
MUTE
PIP SURF
SWAP
FREEZE
PIP MODE
PIP ACCESS
DAY/NIGHT
SOURCE WIZARD
REC
SELECT
TV/RGB
ASPECT
STB
ANT
LAST CH
VID 1
VID 2
VID 3
VID 4
VID 5
PVR
CD
AMP
VIDEO
MY SATELLITE RECEIVER/STB CODE IS:
NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-
box/satellite receiver.
THE REMOTE CONTROL