Filter
Top Products
POWE
R
TV
V
CR
C
BL
DVD
1
2
4
5
6
3
7
89
0
INFO
SLEEP
A/V N
E
T
EXIT
M
ENU
C
HVOL
M
U
T
E
P
I
P
P
I
P
C
H
SWA
P
FR
E
EZE
PIP MODE
PIP A
C
CESS
VIDEO
SOURCE WI
Z
ARD
REC
S
ELECT
T
V/RGB
ASPECT
S
TB
ANT
LA
S
T C
H
VC
R PL
U
S
+
S
V
C
S
G
U
I
D
E
/
T
V
S
CH
D
V
I
D
1
V
ID 2
V
I
D
3
V
I
D
4
VID
5
TA
P
E
C
D
A
MP
MODE
C
L
U-5723
TS
I
39
USING YOUR REMOTE
TO CONTROL ADDITIONAL AUDIO EQUIPMENT
Operating the precoded function for your Audio component.
This remote is designed to operate different types of Audio component. You must first program the remote to match the remote com-
mand set of your Audio component (refer to page 40 for pre-codes).
1. Turn ON your Audio component you wish to control with the Remote.
2. Aim the remote control at the front of your Audio component.
3. Press and release the CD, PVR, or AMP button to switch to Audio component pre-coded mode.
4. Hold down the CD, PVR, or AMP button on the remote and enter the two digit preset code that matches your Audio component, as
shown on page 40. The CD, PVR or AMP button light will flash 3 times if the code was accepted.
5. Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component if the cor-
rect two digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio
component does not turn off, try a different two digit preset code.
6. The remote will now control your Audio component.
7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. Be sure to use a different Audio button
on the remote, since only one component can be programmed per button.
NOTES:
1. If your Audio component cannot be operated after
performing the above procedures, your Audio
component’s code has not been precoded into the
remote.
2. In the unlikely event that your Audio component cannot be
operated after performing the above procedures, please
consult your Audio equipment operating guide.
3. The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
ቢ CD, PVR, AMP Buttons
These buttons allow the remote to control your Audio
equipment by setting it to Audio mode.
ባ PRECODED AUDIO Buttons
These buttons transmit the chosen precoded Audio
component codes.
ቤ EXCLUSIVE TV Buttons
These buttons are for operating the Plasma TV.
ቢ
ባ
ቤ
ቤ
ባ
ቤ
POWER
TV
VCR
CBL
DVD
1
2
4
56
3
7
89
0
INFOSLEEP
A/V NET
EXIT
MENU
CHVOL
MUTE
PIP SURF
SWAP
FREEZE
PIP MODE
PIP ACCESS
DAY/NIGHT
SOURCE WIZARD
REC
SELECT
TV/RGB
ASPECT
STB
ANT
LAST CH
V
ID
1
VID 2
VID 3
V
ID 4
V
ID
5
PVR
CD
AMP
VIDEO
MY AUDIO EQUIPMENT CODE IS:
NOTE: Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.
CD
PVR
AMP/RCVR
THE REMOTE CONTROL