19
THE GENIUS REMOTE CONTROL
In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different
types of VCRs, CATV (Cable TV) converters, satellite receivers, DVD players, and other audio/video equipment with one touch.
Basic operation keys are grouped together in one area.
To operate your TV, point the remote control at the remote sensor of the TV and press the TV button. The TV button will blink,
indicating that the remote will now control your television.
To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The VCR button will blink,
indicating that the remote will now control your VCR. (See page 26 for instructions on how to program the remote to control your
VCR.)
To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The CBL
button will blink, indicating that the remote will now control your cable box. (See page 27 for instructions on how to program the
remote to control your cable box.)
To operate your set-top-box, point the remote at the remote sensor of the your set-top-box and press the SET-TOP-BOX (STB)
button. The STB button will blink, indicating that the remote will now control your your set-top-box. If you have a satellite
receiver, use this button to program your satellite receiver. (See page 28 for instructions on how to program the remote to control
your satellite receiver.)
To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The DVD button
will blink, indicating that the remote will now control your DVD player. (See page 29 for instruction on how to program the remote
to control your DVD player.)
To operate additional audio/video equipment, point the remote at the remote sensor of the component you wish to control and
press the AV1, AV2 or AV3 button. This button will blink, indicating that the remote will now control the desired component. (See
page 30 for instructions on how to program the remote to control additional Audio/Video equipment.)
ቢ These buttons allow the remote to control your TV, VCR,
cable box, satellite receiver, DVD player, or other
Audio/Video equipment depending on which mode is
chosen, as explained above.
ባ,ቤ LIGHT BUTTON
When you are in a dark room, press the light button ባ
on the remote to light up the buttons shown in ቤ and the
source button will blink. Thelight will stay on for about 8
seconds if the light button is not pressed again. These
buttons will not appear to light if the room is too bright.
NOTE: 1. Your remote control SOURCE WIZARD buttons
are either labeled as AV1, AV2 and AV3, or CD,
TAPE, and AMP. If your remote control
SOURCE WIZARD buttons are labeled as AV1,
AV2, and AV3, please program your Audio/Video
components as follow for best performance. Use
AV1 to program your CD brand. Use AV2 to
program your TAPE brand, and use AV3 to
program your AMPLIFIER/RECEIVER brand.
AV1-Use for CD brand
AV2-Use for TAPE brand
AV3-Use for AMPLIFIER/RECEIVER brand.
AV2
AV1
AV3
DVD
SOURCE WIZARD
POWER
TV
VCR
CBL
DVD
1
2
4
56
3
7
89
0
LAST CHSLEEP
HELP
EXIT
MENU
CHVOL
M
UTE
PIP PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
SELECT
ቢ
ባ
ቤ
ቤ
ቤ
STB
INPUT
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
AV2
AV1
AV3
PIX
CLU-5712TSI
POWER
TV
VCR
CBL
DVD
1
2
4
56
3
7
89
0
LAST CHSLEEP
HELP
EXIT
MENU
CHVOL
MUTE
PIP PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
SELECT
ቢ
ባ
ቤ
ቤ
ቤ
STB
INPUT
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
TAPE
CD
AMP
P
IX
CLU-5714TSI