Filter
Top Products
PC MODE CONNECTION AND OPERATION
68
IMPORTANT: TURN OFF THE REAR PROJECTION TV/PC MONITOR AND THE PC BEFORE CONNECTING OR
DISCONNECTING ANY CABLES.
ANT A
TO
CONVERTER
ANT B
12345
678910
1112131415
AUDIO
L
R
(MONO)
VIDEO
VIDEO
AUDIO
(MONO)
L
R
AUDIO
(MONO)
L
R
VIDEO
S-VIDEO
Y
S-VIDEO
Y
B
R
P
P
B
R
P
P
S-VIDEO
L
R
L
R
SUB
WOOFER
STOP
CONNECT ONLY 8 OHM SPEAKERS
DO NOT SHORT CIRCUIT
THESE TERMINALS
(Such damage is NOT COVERED
by your television warranty)
REAR SPEAKER
8Ω ONLY
-
L
+
-
+
R
OPTICAL
INPUT
COAXIAL
INPUT
PC RGB INPUT 1
PC AUDIO
INPUT 1
MONITOR
OUT
INPUT 2
INPUT 1
AUDIO
TO HI-FI
AUDIO OUT
12345
678910
1112131415
RGB
OUTPUT
D-SUB 15 Pin
RGB Cable
(Optional)
Audio Cable
(Optional)
Rear Panel of Television
REAR PANEL
CONNECTION TO PC
This PC ready Rear Projection Television can automatically detect and display PC signal format.
1. RGB input signal.
This PC ready Rear Projection Television can accept the following signal formats.
Preset Timings
No. Formats Horizontal No. Formats Horizontal
Frequency Frequency
1 VGA 640x400 70.1Hz 31.48kHz 13 XGA 1024x768 60.00Hz 48.36kHz
2 VGA 640x480 59.95Hz 31.48kHz 14 XGA 1024x768 70.07Hz 56.48kHz
3 Mac13” 640x480 66.67Hz 35.00kHz 15 XGA 1024x768 75.03Hz 60.02kHz
4 VGA 640x480 72.81Hz 37.86kHz 16 Mac19” 1024x768 74.93Hz 60.24kHz
5 VGA 640x480 75.00Hz 37.50kHz 17 XGA 1024x768 85.00Hz 68.68kHz
6 VGA 640x480 85.01Hz 43.27kHz 18 Mac21” 1152x870 75.06Hz 68.68kHz
7 SVGA 800x600 56.25Hz 35.16kHz 19 SXGA 1280x1024 60.02Hz 63.98kHz
8 SVGA 800x600 60.32Hz 37.88kHz 20 SXGA 1280x1024 75.02Hz 79.98kHz
9 SVGA 800x600 72.19Hz 48.08kHz
10 SVGA 800x600 75.00Hz 46.88kHz
11 SVGA 800x600 85.06Hz 53.67kHz
12 Mac16” 832x624 74.55Hz 49.72kHz
D-SUB 15 Pin
RGB Cable
(Optional)
PC
AUDIO OUT
Back of PC
udio Cable
Optional)
̇
VIDEO 3
VOL-
̇
̇
AUDIO IN
VIDEO 3/PC2
L/(MONO) R
VIDEO
S-VIDEO
PC2
12345
678910
1112131415
INPUT
VOL+
CH-CH+
TV/PC
EXIT
MENU
̈
SELECT
FRONT PANEL
CONNECTION TO PC
NOTE: 1. Dots correspond to the true resolution in Real Mode of aspect ratio, when you select signal of No. 1 to No. 12 on the
table above. (One dot corresponds to one pixel).
2. The signal which resolution exceeds either 1280 dots or 720 lines may not display truly due to compression, then edges
of the picture are slightly hidden.
3. Both vertical and horizontal picture in full mode and vertical picture in normal mode are overscanned.
4. We recommend you change either refresh rate or resolution setting of your video card at control panel from 60Hz to
70Hz, if you see noise on the picture with XGA 60Hz.
5. Always reset AUTO ADJUST feature when setting new display setting (VGA,SVGA,XGA) or when changing to a new
computer.