Filter
Top Products
11
NS-27RTV 27-inch Color TV
www.insignia-products.com
Setting a password
To set a password:
1 Press MENU. The menu screen appears.
2 Press or to select the LOCKS menu.
3 Press
or to display the password
entering mode.
4 Select and enter a password (4 digits) using
the number buttons (0-9), then press ENTER.
5 Enter the same password again to confirm,
then press ENTER.
The password is now set and the V-Chip
menu appears on the screen.
Setting the V-Chip
To set the V-Chip:
1 Press MENU. The menu screen appears.
2 Press or to select the LOCKS menu.
3 Press
or to display the password
entering mode. Use number buttons (0-9) to
enter your password, then press ENTER.
The LOCKS menu appears.
4 Press or to select V-CHIP SET, then
press . The
V-CHIP SET
menu appears.
5 Press
or to select TV RATING, then
press or to display the desired rating.
OFF—TV RATING is not set
TV-Y—All children
TV-Y7—7 years old and above
TV-G—General audience
TV-PG—Parental guidance
TV-14—14 years old and above
TV-MA—17 years old and above
When you select TV-Y7, TV-PG, TV-14, or
TV-MA, press -/DISPLAY to further define the
rating. Press
or to select the desired
rating you want. Press or to select the
setting ON or OFF.
6 Press or to select MOVIE RATING,
then press . The
RATING
menu appears.
7 Press or to select the rating, then
press or to select ON or OFF for each
rating.
OFF—MOVIE RATING is not set
G—All ages
PG—Parental guidance
PG-13—Parental guidance less than 13
years old
R—Under 17 years old parental guidance
suggested
NC-17—17 years old and above
X—Adult only
8 Press MENU twice to return to the
LOCKS
menu, then press or to select V-CHIP.
9 Press or to select ON. Your settings are
now set into memory.
10 Press EXIT to return to the normal screen.
Watching a protected show
To watch a program that is blocked by the
V-Chip:
1 Press MUTE.
2 Enter the password, then press ENTER.
After you enter the password correctly, the
protection is temporarily overridden. If the
television is turned off, or if the channel is
changed, the V-Chip restriction is reactivated.
Changing the password
To change the password:
1 Press MENU. The menu screen appears.
2 Press or to select the LOCKS menu.
3 Press
or to display the password
entering mode. Use the number buttons (0-9)
to enter your password, then press ENTER.
The LOCKS menu appears.
4 Press
or to select NEW PASSWORD,
then press or .
5 Enter a new password using the number
buttons (0-9), then press ENTER.
6 Enter the same password again to confirm,
then press ENTER.
7 Press EXIT to return to the normal screen.
Locking channels
With the CH LOCK feature, you can lock specific
channels. You cannot tune locked channels
unless you clear the setting. You can choose to
lock up to 12 television channels.
To lock channels:
1 Use the number buttons (0-9) to display the
television channel you wish to lock.
2 Press MENU, then press or to display
the LOCKS menu.
3 Press
or to display the password
entering mode.
4 Use the number buttons (0-9) to enter your
password, then press ENTER. The LOCKS
menu appears.
5 Press
or to highlight CH LOCK and
press or to display the CH LOCK menu.
6 Press or to select the following:
• SET– to set the channel as one to be
locked, then press ENTER.
• CLEAR– to clear all channels from the list
of locked channels, then press ENTER.
Notes
• The V-Chip function is activated only
on programs and input sources that
have the rating signal.
• It may take several minutes to
complete the initial V-Chip setup.
• The V-CHIP SET (DTV) will only be
selectable when the TV receives a
digital broadcast using the new rating
system. Currently, some stations are
still not providing this signal. If the
signal is not provided, V-CHIP SET
(DTV) function will not be available.
• If you forget the password, contact
Customer Service at 1-877-467-4289
for assistance. Your original remote
control is required.
• To avoid forgetting the password, write
it down and keep it in a safe place.
Note
After programming CH LOCK, change the
channel before turning off the television.
Failure to do so cancels the programming for
channels locked using this procedure.