Filter
Top Products
12
DC 12V
PGZ01945
TIMER
TIME CODE
SPARE
COMPONENT
VIDEO
SYNC IN
REC
OFF
PLAY
DV
IN/OUT
REMOTE
AUDIO
2
1
SERIAL
CH 1/3
OUT
OUT
IN
IN
B-Y
IN
Y/C
LINE
OUT
OUT
MONITOR
CH 2/4
MONITOR
OUT
R-Y
Y
3-2 Audio system connections
3 CONNECTIONS
Audio output from a VCR, etc.
Audio input to a VCR, etc.
DV
Mic
Headphones
DV
Analog audio
(2 channels)
Analog audio
(monaural)
Analog audio (2 channels)
Connection with a monitor TV
The audio output from the [AUDIO MONITOR OUT]
connector is monaural.
Use the front panel [AUDIO MONITOR] switch to select the
audio channels you want to monitor. The selected audio
channel is shown in the table below. Adjust the audio
volume level on the monitor.
Headphones jack
Audio can be monitored in stereo using the headphones.
Use the front panel [AUDIO OUTPUT] switch to select the
audio channels you want to monitor. The selected audio
channel is shown in the table below. Adjust the audio
volume level with the front panel [PHONES] control.
Inputs
5
Analog inputs
Audio connectors (CH1/3, CH2/4)
Analog input connectors are only provided for 2 channels.
It is not possible to record 4 channels simultaneously.
Audio input from each connector is normally recorded on
the CH1 and CH2 channels. Recording on the CH3 and
CH4 can be performed in the Audio Dubbing mode with the
No. 245 <SAMPLING RATE> menu switch set to
“32K”.
For audio dubbing, refer to
“Audio dubbing” on page 24.
5
Digital inputs
Digital signals conforming to IEEE 1394 can be input to the
[DV IN/OUT] connector. In this case, the audio recording
level cannot be adjusted. When audio signals are input to
the [DV IN/OUT] connector, some noise will occur at the
point where recording ends. To reduce this noise during
playback, set the No. 214 <V. FADE> menu switch to
“ON”.
5
Mic input jack
Connect a monaural microphone. The same audio is
recorded on both channels.
Outputs
5
Analog outputs
Audio connectors (CH1/3, CH2/4)
Analog output connectors are provided for 2 channels. For
MiniDV format, use the front panel [AUDIO OUTPUT]
switch to select for 4-channel audio. The selected audio
channel is shown in the table below.
5
Digital outputs
Digital signals conforming to IEEE 1394 are output from the
[DV IN/OUT] connector.
Relationship between [AUDIO OUTPUT] / [AUDIO MONITOR]
switch and audio output channel
(During playback with 32 kHz sampling, audio dubbing, and DV
input with the 32 kHz sampling in the EE mode)
Regardless of setting of this switch, CH1/2 is selected for ordinary
recording, record pause and analog audio input in the EE mode.
CH3/4 is selected for audio dubbing in the Pause mode.
Monitor TV
CH1 CH1 CH2
CH1/3 CH1/3 CH2/4
CH3 CH3 CH4
CH1/2 CH1 CH2
CH1/2/3/4 CH1/3 CH2/4
CH3/4 CH3 CH4
CH2 CH1 CH2
CH2/4 CH1/3 CH2/4
CH4 CH3 CH4
R
L
MIX
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
CH1/2
MIX
CH3/4
AUDIO switch Connector
MONITOR OUTPUT MONITOR OUT
AUDIO OUT
CH1/3 CH2/4
13
3-3 Other connections
3 CONNECTIONS
Remote connector
Connect a remote controller to the appropriate connector
(three types are available).
Type of connector Connectable remote
controller
[SERIAL] connector RM-G30
[REMOTE1] connector RM-G820
[REMOTE2] connector RM-G800
Power sockets
2 types of power supply are available (AC, DC).
DC power supply socket
Connect DC 12 V.
AC power supply socket
Connect AC 120 V (U MODEL), AC 220 – 240 V (E
MODEL).
5
Selection of battery type
Set the menu switch according to the type of battery that
will be used.
* If the setting does not correspond to the battery type, the
battery remaining time and battery alarm will not be
correctly displayed.
DC 12V
PGZ01945
TIMER
TIME CODE
SPARE
COMPONENT
VIDEO
SYNC IN
REC
OFF
PLAY
DV
IN/OUT
REMOTE
AUDIO
2
1
SERIAL
CH 1/3
OUT
OUT
IN
IN
B-Y
IN
Y/C
LINE
OUT
OUT
MONITOR
CH 2/4
MONITOR
OUT
R-Y
Y
Note:
• Before connecting the RM-G800, be sure to turn the
VCR OFF. Do not connect or disconnect the remote
cable with the VCR ON.
Note:
• Do not use this unit continuously when the battery
indicator is displayed. The unit may not operate
properly. Remove the battery to avoid over-
discharge.
੬
See “396 BATTERY SELECT” on page 19.
• Used battery
The following batteries can be used with this unit.
• Flat shape type
• Anton Bauer Inc. : Trimpack 13 and 14 series
Pro Pac 13 and 14 series
• IDX Corporation : NP-L46