JVC DR-MH20S DVR User Manual


 
Masterpage:Right+
EN 25
Filename [DR-MH30US_04Name.fm]
INITIAL SETTINGS
Page 25 Thursday, 8 July 2004 15:30
7 Select the output channel.
Your selection depends on how the cable box and/or DBS receiver
is connected to your unit.
If the cable box or DBS receiver is connected to your units
ANTENNA IN connector on the rear panel, press rt to select the
channel number representing the cable boxs output (CH2 CH9),
then press ENTER.
If the cable box or DBS receiver is connected to your units
AUDIO/VIDEO Input connectors on the front panel, press rt to
select F-1, then press ENTER.
If the cable box or DBS receiver is connected to your units
AUDIO/VIDEO INPUT connectors on the rear panel, press rt to
select L-1 or L-2, then press ENTER.
If you do not use a cable box or DBS receiver, press rt to select
OFF, then press ENTER.
8 Press rt to select CABLE BOX BRAND or DBS RECEIVER
BRAND, then press ENTER. Press rt to select the brand code
from the following list, then press ENTER.
9 Press rt to select TEST MODE, then press ENTER.
8 For cable box
If the cable boxs channel changes to 9, setting is complete.
Press ENTER and CABLE BOX
CONTROL IS ON appears on the
screen for about 5 seconds, then
the screen in step 5 appears.
If the cable boxs channel does
not change to 9;
A Press we to select NO, then
press ENTER.
B Repeat steps 8 9 until the cable boxs channel changes to 9
by entering another code.
C If the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the other
numbers.
8 For DBS receiver
If the DBS receivers channel
changes to the channel listed
below for your brand, setting is
complete.
Press ENTER and DBS
RECEIVER CONTROL IS ON
appears on the screen for about 5
seconds, then press ENTER. The
screen in step 5 appears.
If the DBS receivers channel does not change as shown
above;
A Press we to select NO, then press ENTER.
B Repeat steps 8 9.
NOTES:
The Controller may not work with all types of cable box or DBS
receiver.
If your cable box does not respond to any code between 1 and 28,
you cannot use the Controller to change cable box channels. In this
case, make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled start time of timer recording.
Contact your cable company about the possibility of exchanging your
current cable box with the one compatible with your unit.
If your DBS receiver does not respond to the code, you cannot use
the Controller to change satellite channels. In this case, make sure to
leave the DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
The unit can only change the cable box or satellite channel through
the Controller during timer recording.
If your cable box and/or DBS receiver cannot be operated with a
remote control (because it has no receiving window), you cannot use
the Controller to change its channels. Make sure to leave the cable
box and/or DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
If the units memory backup expires because of a power failure, set
the cable box and/or DBS receiver output channels and brands
again.
For customers in U.S.A.: If you are unable to set the Controller,
contact JVC toll free at 1-800-252-5722.
CABLE BOX BRAND CODE
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
1, 17
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15, 28
10, 18, 23
15
1, 4, 6, 11, 12, 15, 28
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
1, 16, 17
5, 16, 24
2, 8
7, 20
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
1, 4, 16
1, 17
16, 17, 25
3, 9, 22
3, 9, 22
DBS RECEIVER BRAND CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
JVC ] 100 SONY ] 205
ECHOSTAR ] 100 RCA ] 205
PRESS [SET UP] TO EXIT
ENTER
SELECT
EXIT
SET UP
SELECT WITH [ ] THEN PRESS [ENTER]
INITIAL SET UP > CABLE BOX SET
N OYES
DID YOUR CABLE BOX CHANGE TO CHANNEL 09?
PRESS [SET UP] TO EXIT
ENTER
SELECT
EXIT
SET UP
SELECT WITH [ ] THEN PRESS [ENTER]
INITIAL SET UP > DBS RECEIVER SET
N OYES
DID YOUR DBS BOX CHANGE TO CHANNEL 100?
DR-MH30US_00.book Page 25 Thursday, July 8, 2004 3:32 PM