Filter
Top Products
Masterpage:Right+
EN 39
Filename [M150SEK_07Timer Recording.fm]
TIMER RECORDING
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single disc can be used without worrying about how
much recording capacity remains. You can programme each disc
to timer record as many as 8 programmes up to 30 days in
advance.
To Make The Disc For On-Disc Timer Programming
1 Press PROG to access
the Programme Check
screen.
2 Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
● When some
programmes are
recorded on the disc, a
caution message
appears. You can either format the disc (A pg. 67) or insert a
new disc, then re-perform the procedure from step 1.
● When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMMEB, then press ENTER.
3 Press selection keys to
set the desired date
(ADATEB), then press E.
4 Press selection keys to
set the desired start time
(ASTARTB), then press E.
● Each press of FG
increases/decreases the
start time in 1 minute
interval.
● To increase/decrease the
start time in 30 minutes interval, press and hold FG.
5 Press selection keys to set the desired stop time (ASTOPB),
then press E.
● Each press of FG increases/decreases the stop time in
1 minute interval.
● To increase/decrease the stop time in 30 minutes interval, press
and hold FG.
6 Press selection keys to set the desired channel (ATV PROGB),
then press E.
7 Press selection keys to set ADAILY/WEEKLYB, then press E.
● For details on ADAILY/WEEKLYB setting, refer to ADaily/Weekly
Recording FunctionB (A pg. 37).
8 Set the other recording
options as required.
● ARecording ModeB
(A pg. 34)
● AModify Title NameB
(A pg. 46)
9 Press ENTER to access
the Programme
Confirmation screen.
10 Press ENTER to
complete ATo Make The Disc For On-Disc Timer
ProgrammingB.
● To programme another timer using ATo Make The Disc For On-
Disc Timer ProgrammingB, repeat steps 1 - 10.
11 Press DVD A to turn off the power.
● is displayed on the front display panel.
● To disengage the timer mode, press DVD A again.
On-Disc Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
● Slide the TV/DVD switch to DVD.
ATTENTION:
● On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
● If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
● If timer programming cannot be set or cancelled, wait for about
40 seconds and then try again.
(FGDE)
ENTER
PROG
DVD A
AUX
DVD
TV
Selection Keys
Satellite Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
A Perform On-Disc Timer Programming.
● In step 6, press AUX to set ATV PROGB to ASATB. Then press
FG to enter the channel position for the satellite broadcast.
B Set the satellite receiver to the appropriate channel for
recording.
● Leave the satellite receiver’s power on.
PROGRAMME CHECK
DISC TIMER PRGM
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
OK
SELECT
PROG
EXIT
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DATE
START
TV PROG
REC MODE
DAILY/WEEKLY
STOP
LP
DISC TIMER PRGM
DATE
START
STOP TV PROG
05/07 SAT
DAILY/WEEKLY
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
WEEKLY
REC MODE
CONFIRM
SELECT
PROG
EXIT
LP
YORN120:3018:30
DISC TIMER PRGM
DATE
START
STOP TV PROG
05/07 SAT
DAILY/WEEKLY
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
WEEKLY
REC MODE
CONFIRM
SELECT
PROG
EXIT
M150SEK_00.book Page 39 Wednesday, June 15, 2005 4:04 PM