Filter
Top Products
Masterpage:Right+
EN 45
Filename [MV5S_08Basic TimerDub.fm]
EDITING
Page 45Wednesday, 8 June 2005 11:00
L-2 Select Setting
Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s [L-2 IN/DECODER] connector.
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
(੬ pg. 44).
2 Press rt to select “L-2 SELECT”, then press ENTER.
3 Press rt to select the
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
NOTES:
● If “L-2 SELECT” is set to
“S-VIDEO/RGB”, it is not possible
to output colour signals correctly
from the VHS deck.
● If “L-2 SELECT” is set to “DECODER”, only the DVD deck operates
properly.
*The boldface settings below indicate the settings at your purchase.
8 L-2 SELECT — VIDEO/RGB / S-VIDEO/RGB /
SAT VIDEO/RGB / SAT S-VIDEO/RGB / DECODER
Select “VIDEO/RGB” or “S-VIDEO/RGB” to use this unit as the
recording deck with the player connected to the [L-2 IN/
DECODER] connector, or to use the satellite receiver connected to
the [L-2 IN/DECODER] connector.
VIDEO/RGB: If a connected appliance’s output is compatible with
regular video signals, set to “VIDEO/RGB”.
S-VIDEO/RGB: If a connected appliance’s output is compatible with
Y/C signals, set to “S-VIDEO/RGB”. You can obtain high-quality
picture. (For connection, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.)
Select “SAT VIDEO/RGB” or “SAT S-VIDEO/RGB” to view a
satellite programme with the TV set while the unit is turned off.
(੬ pg. 76)
SAT VIDEO/RGB: If a connected satellite receiver’s output is
compatible with regular video signals, set to “SAT VIDEO/RGB”.
SAT S-VIDEO/RGB: If a connected satellite receiver’s output is
compatible with Y/C signals, set to “SAT S-VIDEO/RGB”. You can
obtain a high-quality S-VHS picture. (For connection, be sure to
use a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER: To use a decoder connected to the [L-2 IN/DECODER]
connector.
NOTES:
● If you have a satellite receiver or a decoder connected to the [L-2 IN/
DECODER] connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the [L-2
IN/DECODER] connector, leave “L-2 SELECT” set to “VIDEO/RGB”.
● When “L-2 SELECT” is set to “SAT VIDEO/RGB” and “SAT S-VIDEO/
RGB”, “SAT” appears on the TV screen or front display panel instead
of “L-2”.
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
“L-2 SELECT” to “DECODER” or “SAT VIDEO/RGB”.
● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2
SELECT” to “DECODER” or “SAT S-VIDEO/RGB”.
● If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT
VIDEO/RGB”, “SAT S-VIDEO/RGB” or “DECODER”, be sure to
connect the [L-1 IN/OUT] connector with a TV.
F-1 Input Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector ([VIDEO] or [S-VIDEO]) being used on the front panel.
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
(੬ pg. 44).
2 Press rt to select “F-1 INPUT”, then press ENTER.
3 Press rt to select the
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
*The boldface settings below
indicate the settings at your
purchase.
8 F-1 INPUT — VIDEO / S-VIDEO
VIDEO: When connecting an appliance to the [VIDEO] input
connector, set to “VIDEO”.
S-VIDEO: When connecting an appliance to the [S-VIDEO] input
connector, set to “S-VIDEO”.
S-VIDEO/RGB
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
OK
SELECT
SET UP
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT
RECORDING SET
OTHERS
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
4:3LB
VIDEO
VIDEO
SCART VIDEO
S-VIDEO/RGB
VIDEO/RGB
SAT S-VIDEO/RGB
DECODER
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
OK
SELECT
SET UP
DVD SET UP
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT
RECORDING SET
OTHERS
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
4:3LB
VIDEO
VIDEO
SCART VIDEO
S-VIDEO/RGB
S-VIDEO
VIDEO
MV5S_08Basic TimerDub.fm Page 45 Wednesday, June 8, 2005 11:00 AM