Filter
Top Products
September 15, 2004 11:23 am Page 11
—11—
Master Page: Right
Express Timer Programming
A Access G-CODE screen
Press PROG.
B Access programme screen
Press START +/–. (If you’re just starting
out, “P1” appears.)
C Enter programme start time
Press START +/– to enter the time you
want recording to start.
● Press and hold START +/– to move in
30-minute increments, or press and
release repeatedly to move 1 minute at
a time.
D Enter programme stop time
Press STOP+/– to enter the time you want recording to stop.
● Press and hold STOP+/– to move in 30-minute increments, or
press and release repeatedly to move 1 minute at a time.
E Enter programme date
Press DATE+/–. (The current date appears on screen. The date you
enter appears in its place.)
F Enter channel position
Press PR +/–.
G Set tape speed
Press p (SP/LP/EP) to set the tape
speed.
H Return to normal screen
After confirming all information is correct, press PROG or OK.
“PROGRAM COMPLETED” appears on the screen for about 5
seconds, then normal screen appears. If “PROGRAM
OVERLAPPED” appears on the screen, see page 12.
● Repeat steps
1 – 8 for each additional programme.
I Engage recorder’s timer mode
Press #. The recorder turns off automatically and “#” appears on
the display panel.
● To disengage the timer, press # again.
NOTES:
● To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps
2 through 8, press WEEKLY (number
key “9”) for weekly serials or DAILY (number key “8”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the screen. Pressing the button again makes the
corresponding indication disappear.
● You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on screen. To record the
extra programme, you must first cancel any unnecessary
programmes (
੬ 12).
24H Express Timer Programming
You can programme a timer recording that starts within 24 hours.
A Access 24HR Express Timer Programme display
Push 24H EXPRESS #. “ ” and start time starts blinking on the
display panel.
B Set programme start time
Turn the JOG dial to the left or right. Then, push the JOG dial.
● One click stop of the JOG dial changes the time in 5-minute
intervals.
C Set programme stop time
“ ” and start time starts blinking on the display panel.
Turn the JOG dial to the left or right. Then, push the JOG dial.
● One click stop of the JOG dial changes the time in 5-minute
intervals.
D Set channel position
Channel number will start blinking.
Turn the JOG dial to the left or right. Then, push the JOG dial and
channel set number will start blinking.
● You can cancel the setting at any time by pressing and holding
the JOG dial for more than 3 seconds. Repeat from the step
2.
● To set the tape speed, press p (SP/LP/EP). The current setting
for the tape speed appears on the display panel for about 5
seconds. Press p (SP/LP/EP) again to change the setting while
tape speed is displayed.
E Engage recorder’s timer mode
Press 24H EXPRESS #.
The recorder turns off automatically and “#” appears on the
display panel.
NOTES:
● If “Err” appears on the display panel, repeat the steps again.
● When a menu screen is shown, you cannot use 24H Express
Timer programming function. Press MENU to return to normal
screen, and try again.
● You can use 24H Express Timer programming function also
when the recorder is turned off.
● For 24H Express Timer programming function, the program
overlap warning display does not appear even if some programs
overlap each other.
Check, cancel and replace programmes
A Disengage timer mode
Press #, then press 1.
B Access Program Check screen
Press ".
C Access Program screen
Press " again to check more
information. Each time you press ", the
next programme’s information appears.
Before performing the following steps:
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Turn on the TV and select the VIDEO channel (or AV mode).
● Select the appropriate colour system (
੬ 13).
Before performing the following steps:
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Select the appropriate colour system (
੬ 13).
21:00
21:00
25.12
22:00
1
Programme start time indicator
Programme start time indicator
Programme stop time indicator
HR-S6970AG.AJ_EN.fm Page 11 Wednesday, September 15, 2004 11:23 AM