Filter
Top Products
January 24, 2003 11:21 am Page 10
— 10 —
Master Page: Right
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are service designed
to assure safe, accurate timer recording. With this system, your
recorder will start and stop recording when the preset TV
programmes actually start and end — even if the broadcast time of
a preset TV programme is changed.
NOTE:
When you use Express Timer Programming, set the start time (VPS
or PDC time) exactly as advertised in the TV listing.
How to check if the station being received transmits a VPS/PDC
signal (Excepting in Central and Eastern Europe)
A Press ––:–– until the channel position appears on the display
panel.
B Hold down 9 on the remote control for about 5 seconds.
“VPS/PDC” appears blinking on the screen.
If a VPS/PDC signal is detected from the station, “VPS/PDC” will
stop blinking.
If no VPS/PDC signal is detected from the station, “VPS/PDC” will
blink at a slower rate.
C Press ––:–– or 9 on the remote control again to return to
normal screen.
Checking, cancelling or changing programme
settings
A
Disengage timer recording standby mode
Press #, then press 1.
● When “AUTO TIMER” is set to “ON” (
੬
12), press only 1.
B
Access Program Check screen
Press ".
C
Access Program screen
Press " again. Each time you press ",
the next programme’s screen appears.
D
Cancel or change programme setting
To cancel a programme, press &.
To change a programme, press the
appropriate button: START / (number
keys “1” and/or “4”), STOP / (number keys “2” and/or “5”),
DATE / (number keys “3” and/or “6”), DAILY (number key
“8”), WEEKLY (number key “9”), PR / , VPS/PDC (number
key “7”) and/or SP/LP (p).
● To change “TV PROG” to “SAT” for the channel position, press
the number key “0”.
E
Return to normal screen
Press " repeatedly until no Program screen is shown.
F
Re-engage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed
on the display panel.
● When “AUTO TIMER” is set to “ON” (
੬
12), the timer
recording standby mode automatically resumes when you turn
off the recorder.
Program overlap warning display
If “PROGRAM OVERLAPPED” appears, you have another
program overlapping the program you have just made. The
Program Check screen appears and conflicting programs will start
blinking.
Example:
Program 1 (you have just made) and Program 4 overlap each other
A
Select program to modify
Press
rt
, then press OK or e.
● You can only select one of the
overlapping programs.
● If you do not mind this overlap, press
PROG to finish the timer program
setting. The program starting earlier or
program with the lower program
number will be recorded.
B
Cancel or change program setting
To cancel a program, press & when the
Program screen you do not want is
shown.
To change a program, press the
appropriate button: START /
(number keys “1” and/or “4”),
STOP / (number keys “2” and/or
“5”), DATE / (number keys “3” and/or “6”),
PR / and/or SP/LP (p) when the Program screen on which
you want to make changes is shown, then press OK or e.
● If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
Automatic Satellite Programme Recording
You can automatically record a satellite programme which is
timer-programmed on your satellite receiver.
A
Connect a satellite receiver to the L-2 IN/DECODER connector
on the rear panel.
B
Set timer programme on satellite receiver referring to its
instruction manual.
C
Load a cassette with the record safety tab intact.
D
Set “L-2 SELECT” to “A/V” or “SAT”. (
੬
12)
E
To set the tape speed, press SP/LP (p). The current setting for
the tape speed appears on the display panel or the screen for
about 5 seconds. Press SP/LP (p) again to change the setting
while tape speed is displayed.
F
Press SAT# for more than 2 seconds. The recorder turns off
automatically and enter the Automatic Satellite Programme
Recording mode (the SAT# indicator lights up). When signals
come into the recorder from the satellite receiver, the recorder
starts recording (the SAT# indicator blinks). The recorder stops
recording and turns off when signals stop coming in.
NOTES:
● Be sure not to turn on the satellite receiver before the
programme starts broadcasting; otherwise, the recorder starts
recording when the satellite receiver is turned on.
● To disengage the Automatic Satellite Programme Recording
mode, press SAT# (the SAT# indicator goes off).
● Depending on the type of satellite receiver, Automatic Satellite
Programme Recording may not be compatible.
● B.E.S.T. does not work in the Automatic Satellite Programme
Recording mode.
● Power Save mode does not work in the Automatic Satellite
Programme Recording mode.
● Just Clock does not work in the Automatic Satellite Programme
Recording mode.
[PROG] : EXIT
START STOP CH DATE
1 8:00 10:00 3 24.04
2 10:00 10:45 2 25.04
3 11:30 13:00 1 25.04
4 9:00 10:00 92 DAILY
5
6
7
8
PROGRAM OVERLAPPED
[
PROG] : EXIT
START STOP CH DATE
1 8:00 10:00 3 24.04
2 10:00 10:45 2 25.04
3 11:30 13:00 1 25.04
4 9:00 10:00 92 DAILY
5
6
7
8
– PI –
START STOP
9:00 10:00
SP VPS/PDC OFF
DATE TV PROG
25.04 92
(X) : DELETE (+/–)
(PROG) : EXIT
HR-V600_001EN.fm Page 10 Friday, January 24, 2003 11:21 AM