Filter
Top Products
EN 13
Instant ReView
Simply by pressing a single button, the recorder power comes
on, rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
NOTES:
●
Before starting, make sure that the recorder is off and that the
Timer mode is disengaged.
●
Turn on the TV and select the VIDEO channel (or AV mode).
ACTIVATE INSTANT
REVIEW
1
Press REVIEW. The recorder power comes on and the
recorder searches for the index code indicating the start
of the last timer-recorded programme. Once it’s found,
playback begins automatically.
To watch the first of the 3 programmes, press REVIEW
three times. The recorder searches and begins playback
automatically. You can access a programme as far as 9
index codes away from the current tape position.
NOTE:
Instant ReView is not possible while the recorder is in the Timer
mode.
Index Search
Your recorder automatically marks
index codes at the beginning of
each recording. This function gives
you quick access to any one of 9
index codes in either direction.
NOTE:
Before starting, make sure the
recorder is in the Stop mode.
£ 2
AB C D E F
–2 –1 1 2 3
Current position
Index number
This function helps you check contents of unlabeled recorded
tapes at the touch of a single button.
NOTE:
Scene Finder cannot be used when the recorder is in the Record
mode.
FF REW FF REW FF REW
Search Search Search
Scene Finder
10 minutes
on counter
5 seconds10 minutes
on counter
5 seconds 5 seconds
ACTIVATE SCENE FINDER
1
Press SCENE FINDER. The recorder starts forward high-
speed search for 5 seconds and then fast-forwards 10
minutes on the counter. This cycle is repeated until the
end of the tape is reached.
● To start Scene Finder in the reverse direction, press
SCENE FINDER and then press the REW button
within 2 seconds. This cycle is repeated until the
beginning of the tape.
● During Scene Finder, "PLAY" appears blinking on the
display panel. During fast forward or rewind, " "
or " " appears on screen.
STOP SCENE FINDER
2
Press STOP.
NOTES:
●
During Scene Finder high-speed search, you can also hear the
tape sound. During fast forward or rewind, you hear the
current TV sound instead.
●
Scene Finder does not function during Index Search.
Next Function Memory
You can set your recorder's power to go off automatically after
the tape is fully rewound. Before starting, make sure the
recorder is in the Stop mode.
For Automatic Power Off After Tape Rewind . . .
. . . press REW, then press OPERATE within 2 seconds.
NOTE:
If you want the power to be turned off automatically when the
counter reads “0:00:00” (instead of at the beginning of the
tape), press C.MEMORY so that the “M” mark appears before
pressing REW.
Tape Position Indicator
The tape position indicator
appears on screen when, from the
Stop mode, you press FF, REW or
perform an Index Search. The
position of “5” in relation to “0”
(beginning) or “+” (end) shows you
where you are on the tape.
”O.S.D.” (
੬ pg. 5) must be set to
“ON”, or the indicator will not
appear.
NOTE:
Depending on the type of tape used, there may be times when
the indication is not correct.
0
+++
3
1:23:45
fi
fi
ACTIVATE INDEX SEARCH
1
Press PUSH JOG or (™ or £). “™ 1” or
“£ 1” is displayed on screen and search begins in
the corresponding direction.
● To access index codes 2 through 9, press PUSH JOG
or repeatedly until the correct index number is
displayed.
Ex.: To locate the beginning of B from the current
position, press PUSH JOG twice.
To locate the beginning of D from the current
position, press PUSH JOG once.
● When the specified index code is located, playback
begins automatically.
fi
fi
fi
fi