Filter
Top Products
Page 13 January 15, 2004 10:38 am
— 13 —
To use the VCR while it is in timer
recording standby mode
Press TIMER, then press POWER. After you use the VCR, press
TIMER again to put the VCR into timer recording standby mode.
Checking, canceling or changing
program settings
A
Disengage timer
Press TIMER, then press POWER.
● When “AUTO TIMER” is set to “ON” (
੬
pg. 14), you do not
have to press TIMER.
B
Access Program Check screen
Press PROG. CHECK.
C
Access Program screen
Press PROG. CHECK again. Each time you
press PROG. CHECK, the next program’s
Program screen appears.
D
Cancel or change program setting
To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START /
(Number key “1” and/or “4”), STOP / (Number key “2” and/
or “5”), DATE / (Number key “3” and/or “6”), CH /,
DAILY (M-F) (Number key “8”), WEEKLY (Number key “9”) and/
or SP/EP when the Program screen on which you want to make
changes is shown.
E
Return to normal screen
Press PROG. CHECK repeatedly until no Program screen is
shown.
F
Reengage timer recording standby mode
Press TIMER. The VCR turns off automatically and “
#
” is
displayed on the display panel.
● When “AUTO TIMER” is set to “ON” (
੬
pg.14) , the timer
recording standby mode automatically resumes when you turn
off the VCR.
Program overlap warning display
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
conflicting programs will start blinking.
Example:
Program 1 (you have just made) and Program 4 overlap each
other
A
Select program to modify
Press
rt
, then press OK or
e
.
● You can only select one of the
overlapping programs.
● If you do not mind this overlap, press
PROG. to finish the timer program
setting. The program starting earlier or
program with the lower program number will be recorded.
B
Cancel or change program setting
To cancel a program, press CANCEL when
the Program screen you do not want is
shown.
To change a program, press the
appropriate button: START / (Number
key “1” and/or “4”), STOP / (Number
key “2” and/or “5”), DATE / (Number key “3” and/or “6”),
CH /, DAILY (M-F) (Number key “8”), WEEKLY (Number key
“9”) and/or SP/EP when the Program screen on which you want to
make changes is shown, then press OK or
e
.
● If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
During a power failure, the program settings listed in Program
Check Screen will be reset.
PRESS (CHECK) TO NEXT
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
PROGRAM 1
START STOP
8:00 PM 10:00 PM
DATE CH
12/24/04 12 SP
PRESS (CANCEL) TO CANCEL
PRESS (CHECK) TO NEXT
( , ), THEN ( ) (PROG.) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
( , ), THEN ( ) (PROG.) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM 4
START STOP
9:00PM 10:00PM
DATE CH
12/24/04 10 SP
FRI
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
PRESS (PROG.) TO END
– Timer Recording –
HR-J693U_EN-new.fm Page 13 Thursday, January 15, 2004 10:38 AM