Filter
Top Products
Page 5 June 7, 2004 1:31 pm
—5—
Language Setting
A Access Main Menu screen, then
Initial Set screen
Press MENU on the remote control. Press
rt to place the pointer next to “INITIAL
SET”, then press OK or
e.
B Access Language Select screen
Press rt to place the pointer next to “LANGUAGE”, then press
OK or
e.
C Select language
Press rt to place the pointer next to the
language of your choice (English,
Chinese or Russian), then press OK or
e.
Press MENU to return to normal screen.
Clock Setting
A Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press rt to place the
pointer next to “INITIAL SET”, then press OK or
e.
B Access Clock Set screen
Press rt to place the pointer next to
“CLOCK SET”, then press OK or
e.
C Set time, date and year
Press rt until the desired time appears,
then press OK or
e. Set the date and year
in the same way.
● Holding
rt changes the time in
30-minute intervals, or changes the date
in 15-day intervals.
NOTE:
If the year digits are automatically cleared, it is possible that you
have input February 29th in a non-leap year. Input the correct
data.
D Start clock
Press MENU and normal screen appears.
To make corrections any time during the process
Press OK or
e repeatedly until the item you want to change
blinks, then press
rt.
Playback
Basic Playback
A Load a cassette
Make sure the window side is up, the rear label side is facing you
and the arrow on the front of the cassette is pointing towards the
recorder.
● Do not apply too much pressure when inserting.
● The recorder turns on, and the counter on the on-screen display
is reset, automatically.
● Select the appropriate colour system with “PAL/MESECAM” and
“NTSC” in Function settings.
● If the cassette’s record safety tab has been removed, playback
begins automatically.
B Start playback
Press 4.
[ / ]
[MENU] : EXIT
MAIN MENU
FUNCTION SET
TUNER SET
INITIAL SET
[ / ]
[MENU] : EXIT
INITIAL SET
CLOCK SET
LANGUAGE
G-CODE/SHOWVIEW SETUP
*
* For HR-V610AG and
HR-V610AJ only
[ / ]
[MENU] : EXIT
INITIAL SET
CLOCK SET
LANGUAGE
G-CODE/SHOWVIEW SETUP
* For HR-V610AG and
HR-V610AJ only
*
[ / ]
[MENU] : EXIT
CLOCK SET
TIME DATE YEAR
0 : 00 01.01 03
Turn on the TV and select the video channel or AV mode.
ATTENTION
In the search, still, slow-motion or frame-by-frame playback
mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour
During playback
Stop playback
Press 8 on the remote
control.
OR Press 0 on the recorder.
Pause playback and view still picture
Press 9.
● Press
4 to resume normal playback.
Pause and Frame-by-Frame playback
Press 9 to pause, then press 6 (or 9 ) repeatedly.
● Press
4 to resume normal playback.
Picture search
Press 3 or 5. Press 3 or 5 again to perform high-
speed search.
● Each time you press
3 or 5, the search speed changes
between low-speed and high-speed.
● Press
4 to resume normal playback.
Variable speed picture search
Press w or e repeatedly.
● Press 4 to resume normal playback.
● Each time you press
w or e, the playback speed changes. To
decrease the speed during picture search, press the opposite
direction button repeatedly.
● During still picture, press and hold
e to start forward (or w to
start reverse) slow motion playback. When you release the
button, still picture resumes. During still picture, holding
9 for
more than 2 seconds also starts forward slow motion playback.
If you press
9 again, still picture resumes.
– Initial Settings –
HR-V610AA.AG.AJ_EN_B.fm Page 5 Monday, June 7, 2004 1:31 PM