JVC HR-XVC19BUS DVD Player User Manual


 
15
Preparation
TUNING
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Auto Channel Programming
1. Choose the SOURCE SELECT option, then
use b / B to select TUNER.
Use b / B to switch among TUNER, LINE1, and
LINE2.
2. Choose the AUTO CHANNEL SET option,
then use b / B to find channels.
The tuner will automatically cycle through all
available channels (TV/CATV) in the area and
place them in the tuners memory.
After the AUTO CHANNEL SET is complete, the
TUNING menu will hide and return to the TV
screen automatically.
If the power fails or the DVD+VCR is unplugged
the channel settings are kept in memory for only 3
seconds.
3. Make sure the TUNING BAND is set appropri-
ately (TV or CATV).
TV : If you are using a standard antenna to
receive channels.
CATV : If you are using basic cable to receive
channels.
To Add or Erase Channels
This feature allows you to add or erase channels
from memory manually.
1. Choose the CH. ADD/DEL option, then use b
/ B to select a channel to add or erase.
2. Use ENTER / OK to add or erase the channel.
Repeat steps 1 and 2 to add or erase other
channels.
3. Press SETUP MENU to return to the TV
screen.
SETUP
FUNCTION OSD
The on-screen display can be turned on or off.
AUDIO MODE
The DVD+VCR has two separate audio playback
systems, the high quality VHS Hi-Fi system and
standard NORMAL mono system. The same
audio is generally recorded on both systems. The
VHS Hi-Fi system plays on separate (left and
right) channels, and the NORMAL system plays
monaural sound. The normal track is always
played so the cassette can be played on a
DVD+VCR that does not have VHS Hi-Fi.
BROADCAST TYPE (STEREO / SAP / MONO)
Multichannel Television Sound (MTS) carries
stereo and/or Second Audio Program (SAP) bilin-
gual signals. Set this display to the desired posi-
tion when both MTS stereo and SAP signals are
received. When only one of the MTS signal is
received, the DVD+VCR automatically selects the
corresponding receiving mode (Stereo or SAP)
regardless of the selected position. For normal
operation, the display should be in the STEREO
position. The DVD+VCR will then record a
STEREO program when available, and record a
mono program IF the program is NOT IN
STEREO. For weak STEREO and/or SAP broad-
casts, changing the display to mono may give
clearer sound.
AUDIO OUTPUT (STEREO / LEFT / RIGHT)
Used during playback [when AUDIO MODE (HI-FI/
NORMAL) is in HI-FI position] for selecting the
audio output signals from the AUDIO OUT termi-
nals (L ch and R ch), and RF.OUT. This display
setting should normally be left in the stereo posi-
tion, so that when a stereo tape is played, the
stereo sound will be heard through the left and right
channels. If a mono tape is played and the audio
output is set to stereo, the same mono sound will
be heard from both left and right channels.
In addition to the above settings, these other
sources are also affected:
1. Playback of CD, DVD or VCD
2. Output of built in tuner, Line 1 or Line 2
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤✤✴✹✲✺✲✵✸✤✤✵✵✾✴✻✤❅M✤✤y✵