Filter
Top Products
EN
23
Adjusting tracking condition
— Tracking Adjustments
Automatic tracking adjustment
This VCR automatically adjusts the tracking condition.
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, use the manual tracking following the
procedures below.
● You can also use the manual tracking during slow
motion playback (੬ pg. 29).
1 Activate manual tracking
Press SP/EP on the Remote during playback.
2 Eliminate the noises on the TV screen
Press CH + or – on the Remote.
● Press it briefly for a fine adjustment, or press and
hold for coarse adjustment. Watch the screen and
continue adjustment until optimum picture and
sound quality are achieved.
● To reactivate automatic tracking, press SP/EP on
the Remote. The automatic tracking becomes
active again.
Selecting monitor sound
— Audio Monitor
You can select the desired monitor sound.
While playing back a tape on which stereo sound or SAP
sound is recorded, press A. MONITOR on the Remote.
Each time you press the button, sound changes as follows:
HI-FI: Normally select this.
Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R:Sound on the right Hi-Fi channel is played back.
NORM:Sound on the normal track is played back.
NORM HI-FI:
Both sounds on the Hi-Fi track and normal
track are mixed and played back.
NOTES:
●
The above indication appears when “SUPERIMPOSE” is set to
“ON” (
੬
pg. 39, 40), though the monitor sound changes in
sequence.
●
If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
●
If RF connection (
੬
pg. 7) is used for viewing pictures on the
TV, sound will be monaural even though you select “HI-FI”.
●
You can also use the menu to select your desired monitor
sound. (
੬
pg. 42)
NORM
NORM
HI-FI
HI-FI
HI-FI L HI-FI R
D
E
F
Automatic operations after
rewinding — Next Function Memory
The Next Function Memory “tells” the VCR what to do
after rewinding is complete.
● Ensure that the VCR is in stop mode.
a– For Automatic Playback Start
Press REW ( 1 ), then press PLAY ( 3 ) within
2␣ seconds.
b– For Automatic Power Off
Press REW ( 1 ), then press POWER within
2␣ seconds.
c– For Automatic Timer Standby
Press REW ( 1 ), then press TIMER within
2␣ seconds.
NOTE:
It is not possible to select the Automatic Timer Standby function
if the cassette’s record safety tab is removed.
Locating beginning of
recordings — Index Search
Index codes are placed on the tape at the beginning of
each recording when recording on this VCR. You can
find and automatically play back from the beginning of
any recording using the Index Search function.
1 Start search
While the tape is not running, press SHUTTLE PLUS
4 or ¢ on the Remote.
2 Access distant code
To access a recording of 2 to 9 index codes away,
press SHUTTLE PLUS 4 or ¢ repeatedly until
the correct number is displayed on screen (only if
“SUPERIMPOSE” is set to “ON” ; ੬ pg. 39, 40).
Playback begins automatically when the desired
recording is located.
● If you want to find the very beginning of the
desired program, press REW ( 1 ) or FF ( ¡ )
after playback starts.
NOTE:
An index code is not placed on the tape when recording is
resumed from recording pause.
G
Current position
on the tape
Beginning of the current
program recorded
Beginning of the 2nd next
program recorded
–1
1
2
–2
3
Previous
program
recorded
Next
program
recorded
2nd next
4
¢