Filter
Top Products
9
AM LOOP
ANTENNA
VD
N
AUDIO
L
R
L
R
AM EXT
CENTER
FRONT
AV IN / OUT
AV IN
SUBWOOFER
OUT
DIGITAL IN
DIGITAL 3
(TV)
DIGITAL 2
(STB)
DIGITAL 1
(DVD)
CENTER
SPEAKER
SURROUND
SPEAKERS
RIGHT LEFT RIGHT LEFT
FRONT
SPEAKERS
SUB
WOOFER
SURR
(REAR)
CAUTION:
SPEAKER
IMPEDANCE
8
~
16
VCR TV
DVD STB
AV IN/OUT
AV IN
TV
VCR
STB
VCR
TV
DVD
STB
*
RX-ES1SL
Getting started
SCART connection
SCART cable (supplied: 1 cable)
For TV and video format
• When the TV is equipped with the multiple SCART terminals, refer
to the TV manual to check the available video signals for each
terminal, then connect SCART cable correctly.
• This receiver cannot convert the video signals (S-video or
Composite). When the video signal of one video component is
different from that of the other (for example, one is S-video, the
other is Composite), you may not see the pictures appropriately. In
this case, unify the video signals of all the video components into
S-video or Composite, or you need to switch the video signal of TV
each time you change the source.
For T-V LINK
• You can use the T-V LINK function if you connect a T-V LINK
compatible TV and VCR to this receiver with a fully wired SCART
cables. For details on T-V LINK, refer also to the manuals supplied
with the TV and the VCR.
• Connect a SCART cable to EXT-2 terminal on your JVC’s T-V LINK
compatible TV for the T-V LINK function.
• Some TV, VCR, STB and DVD players’ support the data
communication like T-V LINK. For complete details, refer also to the
manuals supplied with these components.
* For an analogue decoder
To watch or record a scrambled program on your VCR, connect the
analogue decoder to your VCR and select the scrambled channel on
your VCR.
If there is not an appropriate terminal for the decoder connection on
your VCR, connect the decoder to your TV.
Refer also to the manuals supplied with these components.
* For recording pictures from STB
When you connect a STB and a VCR directly with a SCART cable,
you can record the pictures from the STB onto VCR without using the
STB menu screens. For details, refer also to the manuals supplied
with the STB.
For digital sounds
To reproduce the digital sound, use both the digital connection and
the SCART cable connection (see pages 8 and 9).
SCART Terminal Specifications
TV VCR STB DVD
AUDIO L/R ⅜⅜ ⅜⅜
IN
Composite ⅜⅜ ⅜⅜
VIDEO S-video − ⅜⅜⅜
RGB − ⅜⅜⅜
AUDIO L/R ⅜*1 ⅜*1
OUT
Composite ⅜*1*2 ⅜*1*2
VIDEO S-video ⅜*2 −
RGB ⅜*2 −
T-V LINK ⅜*3 ⅜*3 ⅜*3 ⅜*3
*1 The signals input from a SCART terminal cannot be output
through the same SCART terminal.
*2 The video format of the output video signals are consistent with
that of the input video signals. For example, if S-video signals
are input to this receiver, no signals other than S-video signals
can be output from this receiver.
Refer to the manuals supplied with the video components to
check the setting of the input/output video signals.
*3 The signals for the T-V LINK function are always going through
the receiver.
See below.
CONTINUED ON THE NEXT PAGE
01-10.RX-ES1&XV-N55[B]f 03.2.18, 1:47 PM9