Filter
Top Products
28
206-4186
Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.)
(Continued from previous page)
6. Verify the Learning setup information on the next screen, and then press
POWER to transfer the Master TV Setup into the selected Memory Bank on
the LT2002.
Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will
be displayed on the screen while the LT2002 copies the Master Setup. When
the Learning process is complete, a “LEARNING COMPLETE”
message will be displayed.
7. When Learning is complete, disconnect the MPI cable from the Master TV.
(Optional) Set the Clock
Set the time on a Master TV’s clock. (If the time has already been copied from a
TV into the LT2002 clone programmer, you can set the Master TV’s clock by
copying the time from the clone programmer.) The LT2002 can copy the current
time to both a Master TV and to the clone’s internal clock—accurate to within one
minute. (Another reason that the LT2002 should be equipped with fresh, high-
quality alkaline batteries, is for it to keep the time as accurately as possible.)
Since the LT2002’s time cannot be set directly, the current time needs to be
copied from an LG TV equipped with an enabled MPI port.
After the time is copied to the LT2002 clone programmer, the current time will be
maintained and can then be transferred to another TV. (This can be a Master TV
or another TV which has already had the features set up.)
Teach Master TV Setup to Target TV
1. Ensure the Target TV is in Pass-through Mode, and then use the Installer
Remote to enter the Target TV Installer Menu: Press MENU repeatedly until
the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER.
2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER. When
the value changes back to 0, press ENTER again to exit the Installer Menu.
3. Tune/set the TV to an analog channel or Aux source, and then connect the
MPI cable to the MPI port on the Target TV.
4. With “THE CLONE HAS CONTROL OF TV” message on display, press 2 on
the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection
Menu. Then, press ENTER.
5. Select the LT2002 Memory Bank in which the new Master TV Setup is located,
and press ENTER.
6. Verify the Teaching setup information on the next screen, and then press
POWER to transfer the Master TV Setup to the Target TV.
Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be
displayed on-screen during Teaching. When the Teaching process is complete,
a “TEACHING COMPLETE” message will be displayed.
7. When Teaching is done, disconnect the MPI cable from the Target TV, turn
OFF the TV, and unplug the TV power cord for 15 seconds.
8. Reconnect the TV power cord, and turn ON the TV. The Master TV Setup
should be resident on the Target TV.
SAVE TV SETUP IN SELECTED
CLONE MEMORY
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
COPY SELECTED CLONE MEMORY
TO TV
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
SAVE TV SETUP IN SELECTED
CLONE MEMORY
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
COPY SELECTED CLONE MEMORY
TO TV
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
-
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.