Filter
Top Products
24
Once the code has been accepted with two
flashes, you can test the functionality of the
device you have just programmed.
If the device cannot be operated or is difficult to
operate, repeat the code input with the next code
from the list. If no other codes are specified for
this manufacturer, try a code suggested by the
remote control.
Switching over the remote control – with the
suggestions by the remote control (see page
37-43)
Switch on the device to which you want to set the
remote control. Standby is not sufficient!
Using the switch select whether
you want to switch over to a VCR,
DVD player or a Set Top Box.
Press the END and
* EPG but-
tons at the same time (5 secs).
The display at the top left of the
remote control flashes twice.
Enter the numbers 991 one after
the other. The display flashes
once after each number is
entered.
Press the # PIP button to select
the first code.
Hold the remote control pointed towards the
device you want to switch over to. Watch the
device.
Now press the (Play) or O
(On/Off) button on the remote
control.
Wait a moment for the reaction
of the device. If the device does
not react, the code is incorrect.
Press the # PIP button to call the
next code.
Press the (Play) or O (On/Off)
button again.
If the device reacts, press the
*
EPG button to confirm the
code.
EPG
AV
def
wxyz
EPG
wxyz
wxyz
PIP
PIP
jkl
EPG
TV
DVD STB
VCR
TV
DVD STB
VCR
AV
OK
VIDEO AV1 AV2 AVS VGA/XGA DVI COMP.IN
AV Selection
Operating additional equipment
Audio output ”DIGITAL OUT”
The digital audio signal is applied at the
”DIGITAL OUT” socket of the Signal Box. Here,
for example, you can connect an external Dolby
Digital Decoder or the Loewe sound system
”Certos/Concertos”.
An analog audio signal from the TV set or a
VCR or another sound source which is received
at one of the Euro-AV sockets of the Signal Box
is converted into a digital signal (PCM) and
output at the ”DIGITAL OUT” socket.
The digital signal from the DVD player is output
unchanged at this socket.
The digital TV sound or the sound of a DVD/CD
player is only audible through a Digital
Receiver or the Concertos or Certos system.
AV-connection/Select
device
Press the key 0 on the remote
control a little longer; the AV
selection bar is displayed again.
Select the AV connection to
which the sound source, such as
the DVD player, is connected.
Converting the remote control in order to
operate a Loewe DVD player or devices
from other manufacturers
You can switch over the remote control for VCRs,
DVD players and Set Top Boxes if the infrared
code of the equipment type is listed in the code
list or is in the code memory of the RC3.
Switching over is done on the one hand by
entering a four-digit code and on the other hand
the remote control suggests codes which you
can test on the equipment.
If you cannot find the equipment in the code list,
try a suggestion from the remote control.
Even if the manufacturer of the equipment is
included in the code list, it is possible that it
cannot be operated. Not all functions on the
RC3 are available for this equipment.
Switching over the remote control – with
code input – e.g. to the Loewe DVD player
Look for the code number of your equipment in
the code list. The list is sorted according to
equipment type – DVD, VCR, STB – and alpha-
betically according to manufacturer. You will find
one or more code numbers next to the manufac-
turer name.
Using the switch select whether
you want to switch over to a
VCR, DVD player or a Set Top
Box.
Press the END and
*
EPG
buttons at the same time (5
secs). The display at the top left
of the remote control flashes
twice.
Enter the four numbers from
the code list one after the other
(0539 for Loewe DVD player).
The display flashes once after
each number is entered. Twice
after the last number.
If the number was incorrect, the
display flashes for longer. The
code number has not been
accepted.
31963_021_RC3_GB 14.01.2005, 10:40 Uhr24