Filter
Top Products
English
Getting Started 15
Setting the VCR Setup Menu
11
Press SYSTEM MENU and the MAIN menu will
appear.
22
Press
vv
/
VV
to select the SETUP menu, then press
OK.
The SETUP menu will appear.
33
Press
vv
/
VV
to choose a desired option on the
SETUP menu. Then press
bb
/
BB
to choose a
desired setting.
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or off.
" FUNCTION OSD can be switched between ON and OFF by
pressing b/B.
AUDIO MODE
The DVD+VCR has two separate audio playback systems, the high
quality VHS Hi-Fi system and standard NORMAL mono system. The
same audio is generally recorded on both systems. The VHS Hi-Fi
system plays on separate (Left and Right) channels, and the NOR-
MAL system plays monaural sound. The normal track is always
played so the cassette can be played on a DVD+VCR that does not
have VHS Hi-Fi.
" AUDIO MODE can be switched between HI-FI and
NORMAL by pressing b/B.
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or Second
Audio Program (SAP) bilingual signals. Set this display to the desired
position when both MTS stereo and SAP signals are received. When
only one MTS signal is received, the DVD+VCR automatically selects
the corresponding receiving mode (Stereo or SAP) regardless of the
selected position. For normal operation, the display should be in the
STEREO position.
The DVD+VCR will then record a STEREO program
when available, and record a mono program IF the program is NOT IN
STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to
mono may give clearer sound.
" BROADCAST TYPE can be switched between STEREO, SAP, and
MONO by pressing b/B.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE-HI-FI/NORMAL is in
HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo position, so
that when a stereo tape is played, the stereo sound will be heard
through the left and right channels. If a mono tape is played and the
audio output is set to stereo, the same mono sound will be heard
from both left and right channels.
" AUDIO OUTPUT can be switched between STEREO, LEFT, and
RIGHT by pressing b/B.
44
Press SYSTEM MENU when finished.
Channel Selection
This DVD+VCR is equipped with a frequency synthesized
tuner capable of receiving up to 181 channels. These include
VHF channels 2-13, UHF channels 14-69 and CATV channels
1-125.
Preparation:
"
Connect the DVD+VCR to the desired type of antenna or cable
TV system, as shown in Connecting Antenna/Cable TV to
DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
11
Press SYSTEM MENU and the MAIN menu will
appear.
22
Press
vv
/
VV
to select the TUNING menu, then
press OK.
The TUNING menu will appear.
33
Press
VV
to choose the SOURCE SELECT option,
then press
bb
/
BB
to select TUNER.
Press b/B repeatedly to switch among TUNER, LINE1 and
LINE2.
44
Press
vv
/
VV
to choose the AUTO CHANNEL SET
option, then press
bb
/
BB
to set the channel.
The tuner will automatically cycle through all
available channels in the area and place them in the
tuner’s memory.
• After AUTO CHANNEL SET is complete, the TUN-
ING menu will close and return to the TV screen auto-
matically.
55
Make sure the TUNING BAND is set appropri-
ately (TV or CATV).
•
TV : If you are using a standard antenna to receive chan-
nels.
CATV : If you are using basic cable to receive channels.
66
Use CHANNEL (+/–) on the remote control or
CHANNEL (
VV//vv
) on the front panel of the
DVD+VCR to cycle through the channels in
memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from mem-
ory manually.
1 Press
VV
to choose the CH. ADD/DEL option on the
TUNING menu. Press b/B to select a channel to add or
erase.
2 Press OK to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3 Press MENU to return to the TV screen.