Filter
Top Products
HOOKING UP YOUR TV (ANTENNA/CABLE CONNECTIONS)
A
combination antenna
receives normal broadcast
channels (VHF 2-13 and UHF
14-69). Your connection is easy
since there is only one 75Ω
(ohm) antenna jack on the
back of your TV - and that’s
where the antenna goes.
ANTENNA
COMBINATION UHF/VHF
To set the
TV to select only
the channel num-
bers in your area,
see Auto Install on
page 3.
SMART
HELP
If your antenna has a
round connector (75Ω),
then you're ready to connect it
to the TV.
If your antenna has flat
twin-lead wire (300Ω), you
first need to attach the antenna
wires to the screws on a 300
to 75Ω adaptor.
Push the round end of
the adaptor (or cable) onto
the ANT(enna) IN jack on
the back of the TV. If the
round end of the adaptor or
cable is threaded, screw it
down tight.
Y
ou may have two separate
antennas. One antenna is
for VHF channels (2-13) and
the other antenna is for UHF
channels (14-69).
For homes with separate
UHF/VHF antennas, you will
need an optional combiner
before you can connect the
antennas to the TV.
SEPARATE UHF/VHF
300 to 75Ω
Adaptor
Combination
VHF/UHF
Antenna
(Outdoor or
Indoor)
Twin-lead
Wire
Round Cable
75Ω
Back of TV
Back of TV
UHF/VHF
Combiner
75-300Ω Adaptor
Outdoor UHF Antenna
(Twin-lead 300Ω)
Outdoor VHF
Antenna
(Twin-lead 300Ω)
Twin-lead
Wire
Push the round end of the
combiner onto the ANT(enna)
IN jack on the back of the TV.
Attach the separate
UHF and VHF antennas to
the correct screws on the
combiner.
Round
End
Outdoor VHF
Antenna
(Round cable 75Ω)
- 2 -
To order
any optional
accessory, contact
your dealer. Or,
call 1-800-851-8885
and refer to the fol-
lowing part num-
bers to order.
• UHF/VHF
Combiner:
4835 466 97016
• 75-300Ω
Adaptor:
M61009
• 300-75Ω
Adaptor:
4835 218 27003
SMART
HELP
Y
our Cable TV signal may be
a single (75Ω) cable or a
Cable Box installation. In either
case, the connection to the TV
is very easy.
CABLE TV
CABLE/CABLE BOX
If you do not have a
Cable Box, then you're ready
to connect your Cable TV sig-
nal to the TV. Go to step 2.
If you have a Cable Box:
Connect the Cable TV signal
to the IN jack on the Cable
Box.
If you do not have a
Cable Box, connect the Cable
TV signal directly to the
ANT(enna) IN jack on the TV.
If you have a Cable Box:
Use a coaxial cable to connect
the OUT jack of the Cable Box
to the ANT(enna) IN jack on
the TV.
NOTE: The coaxial cable
might be supplied by the Cable
TV company.
Back of TV
Coaxial cable
Cable Box
To select
only the channels on
your Cable system,
see Auto Install
(page 3).
If you use a Cable
Box, set the TV to
the same channel as
the CH 3/4 switch
on the back of the
Cable Box and
select channels at
the Cable Box.
SMART
HELP
Cable TV Company
Cable TV Signal (75Ω)
Note to the Cable TV System Installer: This reminder is provided to call the Cable TV system
installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for
proper grounding - in particular, specifying that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as possible.