Filter
Top Products
2726
CHANGING VOLUME LOCK
The One For All 4-Device Video Expert Plus With
Learning remote control is preset to control the volume
of a component through your TV.
If your TV is not remote controllable,or if you would like
the volume to be controlled by a different component,you
can change the Volume Lock setting to control a volume
through a non-associated mode (e.g.,through the cable in
the TV mode).
To change Volume Lock to the CBL/SAT mode:
1. On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2. Enter 9 - 9 - 3 and then press CBL/SAT once.
The LED will blink twice.
3. Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, the volume will be
controlled by your Cable Converter or Satellite
Receiver.
To change Volume Lock to the VCR mode:
1. On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2. Enter 9 - 9 - 3 and then press VCR once.
The LED will blink twice.
3. Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, volume will be
controlled by your VCR.
To change Volume Lock to the DVD mode:
1. On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2. Enter 9 - 9 - 3 and then press DVD once.
The LED will blink twice.
3. Now,whenever you press VOL +,VOL –,or
MUTE on the remote control, volume will be
controlled by your DVD (or LD) player.
RE-ASSIGNING DEVICE KEYS
The One For All 4-Device Video Expert Plus With
Learning remote control can be set up to control a second
TV or VCR,or any combination of four video compo-
nents.For example,to have the unit control a TV,a Cable
Converter,and two VCRs, you will need to re-assign the
unused DVD key to operate the second VCR as follows:
1. On the remote control,press and hold SET until
the LED blinks twice,then release SET.
2. Enter 9 - 9 - 2.The LED will blink twice.
3. Press VCR once,then press DVD once.The LED
will blink twice.
4. Program the DVD key as a second VCR.See
Programming VCR Control on page 12.
To re-assign other device keys,repeat steps 1 through 4 by
substituting the key sequence from the following chart for
a desired component:
To Re-Assign Perform Key Sequence
VCR as 2nd TV key: SET - 9 - 9 - 2 - TV - VCR
VCR as 2nd DVD key: SET - 9 - 9 - 2 - DVD - VCR
VCR as 2nd Cbl/Sat key: SET - 9 - 9 - 2 - CBL/SAT - VCR
VCR back to VCR: SET - 9 - 9 - 2 - VCR - VCR
DVD as 2nd TV key: SET - 9 - 9 - 2 - TV - DVD
DVD as 2nd VCR key: SET - 9 - 9 - 2 - VCR - DVD
DVD
as 2nd
Cbl/Sat
key:
SET - 9 - 9 - 2 - CBL/SAT - DVD
DVD
back to
DVD
:
SET - 9 - 9 - 2 - DVD - DVD
CBL/SAT as 2nd TV key: SET - 9 - 9 - 2 - TV - CBL/SAT
CBL/SAT as 2nd DVD key: SET - 9 - 9 - 2 - DVD - CBL/SAT
CBL/SAT as 2nd VCR key: SET - 9 - 9 - 2 - VCR - CBL/SAT
CBL/SAT back to CBL/SAT: SET- 9 - 9 - 2- CBL/SAT- CBL/SAT
Upon completion of a re-assignment,the LED will blink
twice to confirm your selection.At that time,you will also
need to program the remote control to control the new com-
ponent (see previous sections on Programming VCR Control,
Programming Cable Converter or Satellite Receiver Control,or
Programming DVD Player Control).